Blastrac 1-16DB4-V2 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 62

Blastrac 1-16DB4-V2 Скачать руководство пользователя страница 4

Organizational Measures

In addition to these operating instructions, general and legal regulations regarding
accident prevention and environmental protection must be compiled with per local
regulations.

Such duties may, for example, relate to the handling of hazardous substances, or the
provision and wearing of personal protection equipment, as well as compliance with
traffic regulations.

The operating instructions must be supplemented by other instructions, including the
duty to supervise and report incident relating to particular working practices, for
example work organization, work procedures, and personnel safety.

Personnel  entrusted  with  working  the  machine  must  read  and  understand  the
operating  instructions  before  starting  work,  paying  specific  attention  to  the  safety
information. To read these instructions after work  has commenced is too late. This
particularly applies to incidental activities such as setting up the equipment, carrying
out maintenance work or training staff to work with the machine.

From time to time the working practices of the operators are to be checked by a
supervisor, especially regarding awareness of safety and hazards.

Operators must tie back long hair and not wear loose clothing or jewelry, including
rings. There is a risk of injury by items getting caught, or being drawn into moving
machinery.

4

Indicates where consultation with the manufacturer is required.

Instructions relating to periodic checks.

Reference to important instructions contained in the operating
instructions.

These operating instructions are to be kept with the machine, and must
be within reach at all times!

Use personal protective equipment if necessary or required by local
regulations! Take notice of all safety and hazard notices on the machine!

«
...
2
3
4
5
6
...
»

Содержание 1-16DB4-V2































































Отзывы:

Нет отзывов