BLACKMER XLW1 1/2 Скачать руководство пользователя страница 12

Страница: 12 / 12

Sliding Vane Pumps: 5 to 2200 GPM

Refined Fuels, Liquefied Gases, Solvents,Process

Stainless Steel Sliding Vane Pumps

1 to 265 GPM: Acids, Brines, Sugars, Syrups,

Beer, Beet Juice, Cider, Flavor Extracts, etc.

System One

Centrifugal Pumps

10 to 7500 GPM; Process, Marine

Magnetic Drive Pumps

Stainless Steel: 14 to 215 GPM

HXL 6, 8 & 10”
Sliding Vane Pumps

130 to 2,220 GPM

Refineries
Terminals
Barges
Ships

Reciprocating Gas Compressors

Liquefied Gas Transfer, Boosting, Vapor Recovery

Hand Operated Pumps

Dispensing, Transfer, In-line

Accessories

Gear Reducers, Bypass Valves, Strainers

Visit

www.blackmer.com

for complete information on all Blackmer products

1809 Century Avenue, Grand Rapids, Michigan 49503-1530 U.S.A.

Telephone: (616) 241-1611 • Fax: (616) 241-3752

E-mail: [email protected] • Internet Address: www .blackmer.com

Содержание XLW1 1/2













Результаты поиска

Содержание XLW1 1/2

Отзывы:

Похожие инструкции для XLW1 1/2

Бренды по названию

Популярные бренды

BLACKMER XLW1 1/2, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание XLW1 1/2

Отзывы:

Похожие инструкции для XLW1 1/2

Бренды по названию

Популярные бренды