background image

BEFORE INSTALLING THE STARTER DISABLE/KEYLESS ENTRY SYSTEM

DO read through this installation manual.

DO NOT install the control module in an engine compartment.

The alarm may arm itself when power is first connected.This is a normal condition.

ITEMS SUPPLIED WITH THE STARTER DISABLE/KEYLESS ENTRY SYSTEM

• 

Receiver and control module

• 

Valet/override switch

• 

Two 2-Button or 3-button, code learning 

• 

LED status indicator

transmitters 

• 

Wiring harness, fuseholder, & fuse

• 

Door lock harness

OPTIONAL ACCESSORIES

Backup battery...............................................

BWS-500

Window roll up...........................................................

WRM-2

Remote starter ..............................................

RAS-101

Power door lock.........................................................

PDL-50

Trunk release .....................................................

TR-100

Relay ....................................................................................

SPDT

Starter disable relay socket.........................

BRS-003

5-wire door lock relay & socket ...............

BRS-008P16

(+) door lock Inverter..............................

BW-34516

SPECIFICATIONS

Operating voltage..................+12 VDC Neg. Ground
Code learning..........................................3 Codes Max.
Current consumption............5 mA (max) disarmed.
Door lock/unlock output .........................(-) 500 mA.
Channel 2 output drive.............(-) 500 mA variable.

Remote control transmit frequency.......................310 mHz.
Passive arming delay..................................30 Seconds approx.
Auxiliary output drive ...............................250 mA maximum.
Flashing output drive .................................(-) 250 mA 30 sec.
Dome light output......................................(-) 250 mA 30 sec.

I N S T A L L A T I O N   M A N U A L

STARTER

DISABLE/

KEYLESS

ENTRY

SYSTEM

I N S T A L L A T I O N   M A N U A L

Содержание BW 752








Отзывы: