Black Horse Model SEA FURY BH148 Скачать руководство пользователя страница 10

10

SEA FURY                       Item code: BH148

.                          

Instruction Manual

  

4)  

Check the fit of the horizontal stabilizer in its 

slot. Make sure the horizontal stabilizer is square and 

centered to the fuselage by taking measurements, but 

don’t glue  anything yet.

B

B

A

A

  

5) 

With the horizontal stabilizer correctly aligned, 

mark the shape of the fuselage on the top and bottom 

of the tail plane using a water soluble / non permanent 

felt-tip pen.

Check  to  mark  sure  the  wing  and  stabilizer  are 

paralell. If they are not, lightly sand the opening 

in the fuselage for the stabilizer until the stabilizer 

is paralell to the wing, but don’t glue anything yet.

A

A

A = A

Top side and

bottom side.

Remove

the covering.

  

6) 

Remove the stabilizer. Using the lines you just 

drew as a guide, carefully remove the covering from 

between them on the top and bottom of the tail plane 

using a modeling knife. 

When  cutting  through  the  covering  to  remove  it,  cut 

with  only  enough  pressure  to  only  cut  through  the 

covering it’s self. Cutting into the balsa structure may 

weaken  it.  This  could  lead  to  possible  failure  during 

flight.

Push in

Top side and

bottom side.

Mark line

Bottom side.

control horn 

1. A+B Epoxy glue

2. Push in

ELEVATOR CONTROL HORN INSTALLATION

Elevator  control  horn  install  as  same  as  the  way  of 

aileron control horn. Please see pictures below.

  

1)  

Elevator install as same as the way of aileron

.

 

Please see pictures below.

  

2)  

Using a modeling knife, cut away the covering 

from the fuselage for the stabilizer and remove it.

  

3) 

Draw a center line onto the horizontal stabilizer. 

Then put the horizontal into the fuselage. 

center line

Содержание SEA FURY BH148

















Отзывы: