Black Box LGB5124A Скачать руководство пользователя страница 136

Страница: 136 / 257

LGB5128A User Manual

126



Application :

Currently the only supported application is MVRP.



Attribute Type :

Currently the only supported Attribute Type is VLAN.



MRP Applicant :

This configuration is used to configure the Applicant state machine behavior for MRP on a
perticular port locally.

•

normal-participant: In this mode the Applicant state machine will operate normally in

MRP protocol exchanges.

•

non-participant: In this mode the Applicant state machine will not participate in the

protocol operation.

The default configuration is normal participant.



Periodic Tx :

This configuration is used to configure transmission mode and this can be configured either
as enabled or disable. The default value of Periodic Tx is disable.



Auto-refresh :

Check the box next to auto-refresh to refresh the information automatically.



Upper right icon (Refresh):

Click on this button to refresh the MRP Port configuration information manually.



Buttons:

Save

– Click to save changes.

Reset-

Click to undo any changes made locally and revert to previously saved

values.

Содержание LGB5124A


































































































































































































































































Результаты поиска

Содержание LGB5124A

Отзывы:

Похожие инструкции для LGB5124A

Бренды по названию

Популярные бренды

Black Box LGB5124A, Руководство пользователя

Результаты поиска

Содержание LGB5124A

Отзывы:

Похожие инструкции для LGB5124A

Бренды по названию

Популярные бренды