Black & Decker REVJ12C, Руководство пользователя

Страница: 6 / 28

6
ENGLISH (Original instructions)
3. Saw blade locking lever
4. Blade clamp
5. Blade support roller
6. Shoe plate
7. Charging port
8. Charger
Assembly
Warning!
Before assembly, ensure the lock-off button is in
the locked position.
Charging the battery (fig. A)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell
temperature warms up or cools down.
u
Insert the charging connector (8) into the charging port (7).
u
Plug in the charging connector (8).
u
Leave the tool connected to the charger for around 4
hours
.
Fitting and removing the saw blade (fig. B)
u
Hold the saw blade (11) with the teeth facing forward.
u
Lift the saw blade locking lever (3) upwards.
u
Insert the shank of the blade fully into the blade clamp (4)
as far as it will go.
u
Release the lever.
u
To remove the saw blade (11), lift the saw blade locking
lever (3) upwards and pull the blade out.
Switching on and off (fig. C)
u
To switch on, slide the lock off switch (2) to the left then
pull and hold the variable speed trigger switch (1). The
speed is determined by the amount the trigger switch is
pulled.
u
To switch off, release the trigger switch (1).
Warning! Do not switch the tool on or off while under load.
Warning! Always slide the lock off switch (2) to the right, the
locked position when the tool is not in use.
Sawing
u
Always hold the tool with both hands.
u
Let the blade run freely for a few seconds before starting
the cut.
u
Apply only a gentle pressure to the tool while performing
the cut.
u
If possible, work with the shoe plate (6) pressed against
the workpiece. This will improve tool control and reduce
tool vibration, as well as prevent the blade from being
damaged.
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
u
Use a fine-tooth saw blade.
u
Saw from the back surface of the workpiece.
u
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw through
this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
u
Use a s aw blade suitable for sawing metal. Use a finetooth
saw blade for ferrous metals and a coarser saw
blade for non-ferrous metals.
u
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut through
this sandwich.
u
Spread a film of oil along the intended line of cut.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
This tool is suitable both for U-shank and T-shank saw blades.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
u
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
u
Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u
Regularly tap bit holder to remove any dust from the
interior.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.