24 • ENGLISH
tools operation. If damaged, have the power tool
repaired before use.
Many accidents are caused
by poorly maintained power tools.
f. Keep cutting tools sharp and clean.
Properly maintained
cutting tools with sharp cutting edges are less likely
to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This
will ensure that the safety of the power tool is maintained.
6. Electrical Safety
Warning!
If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally qualified
person in order to avoid damage or injury. If the power
cord is replaced by an equally qualified person, but
not authorized by Black & Decker, the warranty will
not be valid.
7. Labels on Tool
The label on your tool may include the following symbols:
1. DO NOT OPERATE
your scroll saw until it is completely
assembled and installed according to the instructions.
2. IF YOU ARE NOT
thoroughly familiar with the operation
of Scroll Saws, obtain advice from your supervisor,
instructor or other qualified person.
3. YOUR SCROLL SAW MUST
be securely fastened to a
stand or workbench. If there is any tendency for the stand
or workbench to move during operation, the stand or
workbench MUST be fastened to the floor.
4. THIS SCROLL SAW
is intended for indoor use only.
5. MAKE SURE
blade is properly tensioned before
operating saw.
6. TO AVOID
blade breakage
ALWAYS
adjust blade tension
correctly.
7. MAKE SURE
the blade teeth point downward toward the
table.
8. NEVER
turn the saw
"ON"
before clearing the table of all
objects (tools, scraps of wood, etc.).
9. DO NOT
cut material that is too small to be safely
supported.
10. AVOID
awkward hand positions where a sudden slip
could cause a hand to move into the blade.
11. ALWAYS
keep hands and fingers away from blade.
12. ALWAYS
adjust holddown foot for each new operation.
13. DO NOT USE
dull or bent blades.
14. DO NOT
attempt to saw material that does not have a flat
surface, unless a suitable support is used.
15. MAKE
"relief" cuts before cutting long curves.
16. NEVER
attempt to cut a curve that is too tight for the
blade being used.
17. WHEN
backing a blade out of a workpiece, the blade may
bind in the saw kerf.This is usually caused by sawdust in
the kerf.If this happens, turn
"OFF"
the switch and remove
plug from power source outlet. Wedge Wedge open the
kerf and back blade out of the workpiece.
18. THE USE
of attachments and accessories not
recommended by Black & Decker may result in the risk
of injuries.
19. ALWAYS
hold the work firmly against the table.
20. DO NOT
feed the material too fast while cutting. Only
feed the material fast enough so that the blade will cut.
21. NEVER
start the Scroll Saw with the stock pressed
against the blade.
22. WHEN
cutting a large workpiece
MAKE SURE
the
material is supported at table height.
23. USE CAUTION
when cutting material which is irregular in
cross section which could pinch the blade before the cut
is completed.A piece of moulding for example must lay flat
on the table and not be permitted to rock while being cut.
24. USE CAUTION
when cutting round material such as
dowel rods or tubing. They have a tendency to roll while
being cut causing the blade to "bite." Use a V-block to
control the piece.
25. ALWAYS
release blade tension before removing the
blade from the upper or lower blade holders.
26. MAKE CERTAIN
table tilting lock is tightened before
starting the machine.
27. NEVER
reach under the table while the machine is running.
28. NEVER
perform layout, assembly or set-up work on the
table while the saw is operating.
29. ALWAYS STOP
the saw before removing scrap pieces
from the table.
30. WHEN THE TOOL IS NOT IN USE,
the switch should be
turned to the
“OFF”
position.
31. SHOULD
any part of your Scroll Saw be missing, damaged
or fail in any way, or any electrical component fail to
perform properly, shut off switch and remove plug from
power supply outlet.Replace missing, damaged or failed
parts before resuming operation.
ADDITIONAL SAFETY RULES
FOR SCROLL SAWS
Read
Instructions
Manual
Use
Eye
Protection
Use
Ear
Protection
V ........ Volts
A ........ Amperes
Hz .......Hertz
W ........Watts
min ..... minutes
.... Alternating
Current
.... Direct
Current
n
0
....... No-Load
Speed
.... Class II
Construction
.... Earthing
Terminal
.... Safety
Alert
Symbol
.../min.. Revolutions
or Recipro-
cation per
minute
