5
ENGLISH
IRREGULARLY SHAPED OBJECTS MAY REQUIRE
ADDITIONAL HOLDING MEANS IF THEY CANNOT BE
HELD SECURELY IN VISE.
CAUTION: DO NOT CUT MAGNESIUM WITH THIS
TOOL.
Maximum Cutting Capacity
NOTE:
Capacity shown on chart assumes no wheel wear
and optimum fence position.
USE
Standard Equipment
•
1 14" Metal Cutting Abrasive Wheel
•
1 Wheel Wrench
•
1 Instruction manual
To Carry (fig. 1)
Fold down unit to position where you can carry the saw.
Push in lock pin (X) to lock arm down.
UnLocking (fig. 1)
To unlock tool and raise head, depress motor arm slightly
and pull lock pin (X) out. Motor arm will then pivot upward.
Spark Deflector Adjustment (fig. 1)
To best deflect sparks away from surrounding persons and
materials, loosen the screw (B), adjust the spark deflector
(C) and then retighten screw. Do not allow cordset to come
into contact with deflector or sparks as damage to cordset
may occur.
Depth Stop (fig. 1)
Depth stop is set at the factory for a new 14" wheel to
prevent wheel from cutting into the supporting surface.To
allow more depth of cut, use the flat wrench provided (G) to
loosen the depth stop bolt (M) and raise bolt todesired height
and then turn jam nut (M) clockwise until seated firmly on the
casting. Securely tighten the depth stop bolt before use.
.......................
Use Ear Protection
V .......................Volts
A .......................Amperes
Hz .......................Hertz
W .......................Watts
min.......................minutes
.......................Alternating current
.......................Direct current
n
0
.......................No load speed
.......................Class II Construction
.......................Earthing terminal
.......................Safety alert symbol
.../min...................Revolutions or reciprocationsper minute
ELECTRICAL SAFETY
Warning!
If the power cord is damaged, it must be
replaced by the manufacturer, authorizedBlack & Decker
Service Center or an equally qualified person in order to
avoid damage or injury.If the power cord is replaced by an
equally qualified person, but not authorized by Black
&Decker, the warranty will not be valid.
FEATURES (fig. 1, 4)
A. Lock on Switch
B. Spark Deflector Screw
C. Spark Deflector
D. Base
E. Fence
F. Vise
G. Flat Wrench
H. Crank
I. Vise Level
J. Wheel
K. Guard
L. Spindle Lock
M. Depth Stop Bolt and Jam Nut
N. Trigger Switch
O. Padlock Hole
P. Fence Bolts
X. Lock Pin
POWER SUPPLY
Be sure your power supply agrees with the nameplate
marking. A voltage decrease of more than 10% willcause a
loss of power and overheating.
CUTTING CAPACITY
The wide vise opening and high pivot point provide cutting
capacity for many large pieces. Use the cutting capacity
chart to determine total maximum size of cuts that can be
made with a new wheel.
CAUTION: CERTAIN LARGE, CIRCULAR OR
A x B
Workpiece
Shape:
90°
Cutting Angle
45°
Cutting Angle
A = 4-7/8"
(125mm)
A= 4-1/2"
(115mm)
A = 4-1/2"
(115mm)
A = 3-13/16"
(98mm)
4-1/2" x 5-1/8"
(115mm x 130mm)
4" x 7-5/8"
(102mm x 188mm)
3" x 7-3/8"
(76mm x 229mm)
4-1/2" x 3-13/16"
4-1/8" x 3-3/4"
(105mm x 95mm)
A = 3-13/16"
3-3/4"
(95mm)
A = 4-1/2" x 5-3/8"
(115mm x 137mm)
Содержание BDEL701
Страница 1: ...www blackanddecker com English 3 BDEL701 ...
Страница 8: ......
