background image

w w w. b i s s e l l . c o m  

O

perations

6

Handle position

Press the handle release pedal with 

your foot to place your BISSELL 

Powerforce Pet into one of three  

cleaning positions.
1. Upright-

 For storage and above floor  

cleaning with special tools.

2.  Normal Cleaning- 

Press handle release 

pedal once. Use for most household floor 

cleaning tasks.

3.  Low Cleaning- 

With the vacuum in 

normal cleaning position, press handle 

release pedal again. Use for reaching 

under low furniture such as tables, chairs 

and beds.

Powerfoot height adjustment

The powerfoot/rotating floor brush  

on your BISSELL Powerforce Pet  

Cyclonic can be adjusted to clean  

several floor surfaces. 

NOTE: For optimal cleaning  

performance, adjust to the lowest 

practical setting. If your cleaner is 

difficult to push, adjust to the next 

higher setting. 

1. 

Place handle in upright position. 

2. 

Turn height adjustment knob to desired setting. 

Lowest Setting -

   For bare floors. 

Medium Settings - 

For short and medium  

 

pile carpets.

 

Highest Setting - 

  For plush pile carpets.

3. 

Place the handle into the normal cleaning 

position and the powerfoot will adjust to 

the setting chosen.

NOTE: You may also adjust the  

setting while in the normal cleaning 

position. 

Transporting cleaner

1. 

To move your cleaner from room to room, 

put the handle in the upright position, tilt the 

cleaner back on its rear wheels and push 

forward. 

2. 

The cleaner can also be moved by using 

the carrying handle on the back.

1

2

3

CAUTION:  

Before using your vacuum, make sure 

that the dirt container is in locked  

position and that all filters (inner circular, 

outer circular, pre-motor and post-

motor) are in place. Do not operate 

your vacuum without these filters.

Tip:

Your vacuum 

features a Quick 

Release cord 

wrap. To remove 

the power cord 

quickly and eas-

ily, rotate the 

upper cord wrap 

towards the floor, 

and slip power 

cord from upper 

and lower  

cord wraps.

Tip:

Before cleaning 

under low furni-

ture, check area 

first for objects 

that might harm 

the unit or block 

the vacuum hose.

ATTENTION:  

Some Berber carpets have a tendency to 

fuzz with wear. Repeated strokes in the 

same area may aggravate this condition. 

Consider setting your cleaner on a higher 

than normal setting for this type of carpet.

Carrying  

Handle

Содержание 28F4 SERIES

















Отзывы: