BIRO 3334SS-4003FH-TL Скачать руководство пользователя страница 7

Страница: 7 / 40

1. Interchange of motor current is made in motor outlet box. Leads are properly marked. Changing

instructions are on motor plate or inside junction box cover.

2. All saws are wired 220 volts unless otherwise specified. Be sure motor specifications (voltage, cycle,

phase) match power supply line. Be sure line voltage is up to specification.

3. Connect leads to machine in a manner that will be approved by local electrical inspectors.

WIRING MOTOR

4. We recommend no less than No. 12 wire. If the leads are too light, machine may not have sufficient

cutting power and/or speed.

5. The V-belt is packed loose in machine to prevent deformation, and must be installed on pulleys at time

of wiring motor. Double V-belts are shipped installed on machine.

6. The BIRO Manufacturing Company is not responsible for permanent wiring, connection or installations.

NOTE TO OWNER AND ELECTRICIAN: IF THIS MACHINE IS NOT CORD

AND PLUG CONNECTED TO THE ELECTRICAL SUPPLY SOURCE, THEN

IT SHOULD BE EQUIPPED WITH, OR CONNECTED TO, A LOCKABLE,

MANUALLY OPERATED DISCONNECT SWITCH (1010.147 OSHA).

5. Place removable finger lift with saw guard assembly (Item No. ALH211-SS) on the saw guide bar

(Item No. S116-22) and fasten in place with finger lift fastener knob (Item No. 211A-291Q).

7. The side platter bracket (Item No. S12214B) is packed loose in

the machine and must be installed on the right side of the base

structure with the supplied hardware and checked for proper

adjustment. Stationary platter must be flat.

8. The stationary platter (Item No. TL16163-1) is placed on top of

the base structure and held in place by two push-pull hold

down catches (Item No. TL16212), located on the base structure.

SHARP SAW BLADE. HANDLE WITH EXTREME CAUTION

9. The sliding meat carriage assembly is installed by turning the movable stop assembly (Item No. A16200)

clockwise. After the carriage assembly is in the channel for operation, turn the movable stop

counterclockwise to lock.

10. Post SAFETY TIPS wall chart within easy view of operator. Keep Manual available to operator.

11. Machine MUST be properly grounded. Use qualified electrician to install according to building codes.

KEEP HANDS CLEAR OF SHARP MOVING BAND TYPE SAW BLADE

6. Placing blade on cutter: Hang upper wheel assembly on the hinge bracket. Lift the nylon filler (Item No.

TL177). Hang blade on the upper wheel and hold with right hand. With left hand force the back of the

blade between the front blade cleaners (Item No. 131), located below the nylon filler and insert

the back of the blade in the upper saw guide (Item No. S602B). The blade has already dropped

over the lower wheel. With right hand force the back of the blade between the rear blade cleaners

(Item No. 131). The blade is now ready to be tightened.

• For movable head machine, Press down on the ratchet arm (Item No. TL18010) located at the rear of the

base structure. Turn the upper wheel slowly by hand to ensure proper tracking of the saw blade on the

wheels. Tighten to proper tension. When the tension gauge (Item No. 16197) located at the bottom rear of

the head becomes tight laterally, the blade is at proper tension.

•

For fixed head machine, turn the blade tensioning handle clockwise until the tension mark is even with the

bottom of the upper wheel hinge plate as shown. Carefully turn saw wheels by hand and watch for proper

tracking of blade on the wheels.

Содержание 3334SS-4003FH-TL









































Результаты поиска

Содержание 3334SS-4003FH-TL

Отзывы:

Похожие инструкции для 3334SS-4003FH-TL

Бренды по названию

Популярные бренды

BIRO 3334SS-4003FH-TL, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 3334SS-4003FH-TL

Отзывы:

Похожие инструкции для 3334SS-4003FH-TL

Бренды по названию

Популярные бренды