Billion BiPAC 6404VGP R3 Скачать руководство пользователя страница 35

Страница: 35 / 119

3. Set up VoIP.

SIP:

To use VoIP SIP as VoIP call signaling protocol. Default is set to

Disable.

Region:

This selection is a drop-down box, which allows user to select the country for which the VoIP

device must work. When a country is selected, the country parameters are automatically loaded.

SIP Service Provider:

This section allows you to select the service provider. When the selection is

done, respective parameters below are automatically displayed.

Phone Number:

This parameter holds the registration ID of the user within the VoIP SIP registrar.

Username:

If the username is same as the Phone Number, leave it blank. Otherwise, fill in the space

with your username given by your VoIP provider.

Password:

This parameter holds the password used for authentication within VoIP SIP registrar.

Display Name:

This parameter will be appeared on the Caller ID.

4. Wait for the configuration.

Содержание BiPAC 6404VGP R3
























































































































Результаты поиска

Содержание BiPAC 6404VGP R3

Отзывы:

Похожие инструкции для BiPAC 6404VGP R3

Бренды по названию

Популярные бренды

Billion BiPAC 6404VGP R3, Руководство пользователя

Результаты поиска

Содержание BiPAC 6404VGP R3

Отзывы:

Похожие инструкции для BiPAC 6404VGP R3

Бренды по названию

Популярные бренды