Bil-Jax 45XA, Руководство оператора

Страница: 20 / 52

BILJAX 45XA
18
The ground control station includes the following
controls and Indicators. Refer to Figure 3-1 for
control locations.
1. Key Switch
Turning the key switch to the
PLATFORM
(1
A
) icon
selects operation from the platform. Turning the key
switch to the
GROUND
(1
B
) icon selects operation
from the ground control panel. The center (power
off) position interrupts all electric and hydraulic
power operations except emergency lowering.
Removing the key protects against operation by
unauthorized persons. The key may be removed
with the key switch in any selected position.
2. Battery Condition Indicator
Indicator LEDs light up to indicate the level of charge
remaining in the batteries. A lighted green LED
indicates an adequate charge level. Lighted yellow
LEDs indicate the need for charging soon. A lighted
red LED warns that the battery charge level is low;
boom operations should be halted until the batteries
are recharged.
3-4. Engine Start and Choke
Start a cold engine by pressing the Engine
START
button while pressing and holding the
CHOKE
button.
To start/restart a warm engine, press the
START
button only.
5. Display Panel
The DISPLAY PANEL is a lighted text window that
displays the present operating status or an existing
error condition when the key switch is on.
6. Emergency Stop Button
When pushed in, the emergency
STOP
button
disconnects electrical power to the ground and
platform control stations. The emergency
STOP
pushbutton should only be pressed to immediately
stop all boom motion. To resume control, pull out the
emergency
STOP
button.
7-8. Boom Extend/Retract Buttons
Pressing and holding a desired
SPEED
button and the
BOOM EXTEND
button at the same time extends the
telescopic boom. Pressing and holding a desired
SPEED
button and the
BOOM RETRACT
button at the
same time retracts the boom. Boom motion
continues until the buttons are released or until the
boom reaches a hard stop or a safe travel limit.
9-14. Boom Raise/Down Buttons
Pressing and holding a desired
SPEED
button and the
UPPER
/
LOWER
/
JIB BOOM RAISE
button at the same
time will raise the chosen boom. Pressing a desired
SPEED
button and the
UPPER
/
LOWER
/
JIB BOOM DOWN
button at the same time will lower the chosen boom.
Boom motion continues until the buttons are
released or until the boom reaches a hard stop or a
safe travel limit.
15. Speed Buttons
The
SPEED
buttons along the lower right side of the
control panel must be pressed and held while
selecting a boom function. Four speeds are
available to control the positioning of the boom lift.
16-17. Platform Tilt Buttons
Press and hold any
SPEED
button and the desired
PLATFORM TILT
button at the same time to level the
work platform (levels the platform only, not the boom
lift).
18-19. Boom Rotation Buttons
Pressing and holding a desired
SPEED
button and the
BOOM ROTATION CLOCKWISE
or
COUNTERCLOCKWISE
button at the same time enables the boom to rotate
in the direction selected. The boom will rotate
through 700 degrees until the buttons are released
or the stop is reached.
20-24. Outrigger Controls
For automatic outrigger extension/retraction: Select
EXTEND
or
RETRACT
outrigger button and the
AUTO
LEVEL
button at the same time. To manually extend
or retract the outriggers: Select
EXTEND
or
RETRACT
outrigger button and one of the
OUTRIGGER
buttons
at the same time. The outrigger indicator LEDs light
up when the outriggers are properly deployed and
the boom weight is on the outriggers. Each of the
outer outrigger LEDs indicates load is on the
outrigger footpad. Each of the inner outrigger LEDs,
when flashing, indicate that side is low and needs to
be further raised for leveling. The Auto Level LED
lights up and a buzzer sounds when the boom is
level.