Big Backyard F24015 Скачать руководство пользователя | Manualshive

Страница: 42 / 56

background image

42

[email protected]

Step 25: Cafe Table Assembly

Part 1

Note: Pre-drill all holes using a 1/8” drill bit before installing the lag screws.
A:

Attach 1 (1926) Table Support to the inside of each (1500) Post on the Cafe Wall side through the middle

hole using 1 (LS3) 1/4 x 3” Lag Screw (with flat washer) per board. The distance from ground to the middle hole

should measure 18”. (fig. 25.1 and 25.2)

B:

Make sure both (1926) Table Supports are level then attach to the posts in the remaining holes with 2 (LS3)

1/4 x 3” Lag Screws (with flat washers) per support. (fig. 25.3)

Hardware

Wood Parts

Fig. 25.2

Fig. 25.3

Fig. 25.1

6 x

1/4 x 3” Lag Screw (1/4” flat washer)

2 x

Table Support 2 x 6 x 12-5/16”

1926

LS3

1926

1500

1926

LS3

1/4” Flat

Washer

Cafe Wall Side

18”

1500

1500

1500

«
...
40
41
42
43
44
...
»

Содержание F24015

























































Отзывы:

Нет отзывов

Похожие инструкции для F24015

CRD 2 00-1000S Series

Бренд: Symbol Страницы: 16

Бренд: Y-cam Страницы: 12

Бренд: Gainsborough Страницы: 2

Бренд: Laser Страницы: 8

Бренд: Napoleon Страницы: 4

FireCracker CK17A

Бренд: X10 Страницы: 1

Бренд: Waycon Страницы: 8

Бренд: Wavetronix Страницы: 4

Бренд: X10 Страницы: 2

Бренд: EUROM Страницы: 28

Бренд: S-BOL Страницы: 3

MEDIA WIRELESS DESKTOP 800 -

Бренд: LABTEC Страницы: 12

Бренд: handi quilter Страницы: 2

Бренд: Hama Страницы: 22

Бренд: Growatt Страницы: 10

01 29 9 416 497

Бренд: BMW Страницы: 5

Yepp Nexxt Mini 12080101

Бренд: Thule Страницы: 8

Бренд: York Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды