Big Backyard F24015 Скачать руководство пользователя

Страница: 45 / 56

[email protected]

Step 27: Attach Seat Assembly to Fort

With (1922) Seat Rail facing the fort, attach (1917) Lower Back to (1921) Seat Post using 2 (H2) 1/4 x 2” Hex

Bolts (with lock washer, flat washer and t-nut). (fig. 27.1 and 27.2)

On the other side of the Seat Assembly attach (1920) Seat Bottom to (1921) Seat Post with 2 (H2) 1/4 x 2”

Hex Bolts (with lock washer, flat washer and t-nut). (fig. 27.1 and 27.2)

Attach (1920) Seat Bottom to (1914) Cafe Ground with 2 Corner Braces using 3 (S5) #8 x 1/2” Pan Screws

per brace, as shown in fig. 27.2 and 27.3.

Other Parts

Hardware

Wood Parts

Fig. 27.1

Fig. 27.3

Fig. 27.2

4 x

1/4 x 2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

6 x

#8 x 1/2” Pan Screw

1 x

Seat Bottom 1 x 5 x 17-3/4”

1920

2 x Corner Brace

1914

1/4” Flat

Washer

1920

1922

1917

1921

1914

1/4” Lock

Washer

1/4”

T-Nut

Corner Brace

x 3 per brace

Содержание F24015

























































Результаты поиска

Содержание F24015

Отзывы:

Похожие инструкции для F24015

Бренды по названию

Популярные бренды

Big Backyard F24015, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F24015

Отзывы:

Похожие инструкции для F24015

Бренды по названию

Популярные бренды