BIFFI ALGA-EAC Series Скачать руководство пользователя страница 10

Страница: 10 / 66

June 2020

Installation, Operation and Maintenance Manual

MAN 564_EAC Rev. 2

Installation

Section 2: Installation

•

For lifting unbalanced loads, use ropes of different lengths or chains with
adjustable length.

•

Check each time the conditions of all lifting equipment used and discard it if
not in perfect working order.

•

Do not knot or twist the ropes so as not to reduce the lifting capacity or
produce torsional effects on the load being lifted.

•

Use the utmost caution and remain at a safe distance from lifted actuator
unless absolutely necessary; do not stand or pass under suspended loads.

•

Pay attention in putting under tension the ropes to prevent the load shifting
sideways in an uncontrolled manner.

•

Use slings of such length that the angles of the leg from vertical are as narrow
as possible (

MAX < 20°).

•

During handling, do not transport the suspended actuator above staff
members in charge of the operation.

WARNING

Do not use the lifting eyelets on actuator to lift valve + actuator assembly.

Figure 6

WARNING

Any lifting method different from what described above is strictly forbidden.
Biffi reject any responsibility for damages to goods or injuries to persons coming from
wrong lifting operations.

BIFFI IS NOT LIABLE FOR ANY
PERSONEL INJURY DUE TO
INCORRECT USE

DO NOT DISASSEMBLE TOP OR
BOTTOM COVER.
SPRING LOADED.

POTENTIAL ELECTROSTATIC CHARGE HAZARD

REFER TO IOM

LIFTING LUGS TO BE USED FOR THE
ACTUATOR ONLY. DO NOT LIFT
VALVE AND ACTUATOR TOGETHER

Содержание ALGA-EAC Series



































































Результаты поиска

Содержание ALGA-EAC Series

Отзывы:

Похожие инструкции для ALGA-EAC Series

Бренды по названию

Популярные бренды

BIFFI ALGA-EAC Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALGA-EAC Series

Отзывы:

Похожие инструкции для ALGA-EAC Series

Бренды по названию

Популярные бренды