33
Without tightening, insert screw (111)
along with washer (121) into hole (X),
as shown in Fig.14.
Then position the top left side panel
(33) on the main body (7), Fig. 14.
Without tightening, insert screw (111)
along with washer (121) into hole (X),
as shown in Fig.14.
20.-
Fit spacer (20) onto the arm
support (16), Fig.14, and position it on
the “U” for the main body (7).
Lift the top right side panel and secure
it using screw (110) along with washer
(124), Fig.14.
Now do the same for the left side
panel. Position the stop for the arm
support (21) on the top side panels
and tigthen securely.
21.-
Fit spacer (24) onto the bottom
section of the arm support (16),
Fig.14, and secure it using screws
(110) along with the washers (124),
Fig.14. Fiinish off by securing the side
panels using (111) with their washers
(121), Fig.15.
NOTE:
Once this stage of the
assembly has been completed, all of
the bolts fitted previously should be
retightened securely.
22.-
Next thread cable (64), which is
already mounted on pulleys (F) and
(G) of the top body (7), Fig.16, through
pulleys (H); (I); (J); (K) and (L).
Take the chain hook (94) and join the
end of cable (64), which you have just
threaded through, with the cable
tensioner (97), Fig.16.
23.- FITTING THE GLUTEAL
PUSH BAR.-
Position the gluteal push bar support
(13) on the “U” for the gluteal support,
as shown in Fig.19.
Align the holes on the “U” with the
push bar support (13), fit the spacer
(23) and tighten securely using screws
(110) along with the washers (124).
24.-
Take push bar (14) and insert it
through the gluteal support in the
direction of the arrow, insert the shaft
(25) leaving it centred and fit screw
(118), tighten securely.
25.- FITTING THE BOTTOM
CABLE.-
Take the end of the foot pull-up cable
(65) and by following the arrows
marked on the cable in Fig.18, pass it
through the first pulley (LL), as shown
in Fig.18.
Next, pass the same tip through the
lower pulley (M) and (N), Fig.18.
Continue passing the tip of the cable
(64) through the fourth pulley (O)
Fig.18. Attach the end of the cable to
the cable tensioning nut (49), Fig.18.
26.- FITTING THE GLUTEAL
SUPPORT CABLE.-
Attach the end of the cable to the
cable tensioning nut (49), Fig.19.
Take the other end of the cable (67)
and by following the arrows marked on
the cable in Fig.19, pass it through the
first pulley (P), as shown in Fig.19.
Next, pass the same tip through the
pulley (Q) and (R), Fig.18.
Continue passing the tip of the cable
(64) through pulley (S), (T), (U); (V);
(Y) and (Z) Fig.19.
27.-
Attach
the end of the cable to the
"U" on the tube (8) for the gluteal
support using screw (113) along with
washers (120) and nut (73), Fig.19.
Содержание TTPro G156
