32
Insert screws (101), along with the
curved washers (122) and nuts (126),
and tighten securely, Fig.10.
Manually check that the weight
selector post (50) travels smoothly
along the full length of the weight
guide bars and then tighten screws
(109) securely.
11.-
Now screw the end of the top
cable (66) into the central boss on the
weight selector post (50), Fig.10, and
tighten the lock nut.
12.- FITTING THE GLUTEAL
ACCESSORY.-
Position the rear connection bracket
(11) and attach it to the vertical tube (6),
Fig.11, and the gluteal support tube (8),
fit screws (102) along with the curved
washers (122) and nuts (126).
13.-
Now position the bottom
connection bracket (12), Fig.11, on the
bottom casing bracket (4) and fit
screws (102) along with the washers
(121) and nuts (126). Then attach the
other end onto the gluteal support
tube (8), Fig.11, fit screws (100) along
with the curved washers (122) and
nuts (126) and tighten, Fig.11.
NOTE:
Once this stage of the assembly has
been completed, all of the bolts fitted
previously should be retightened
securely.
14.- FITTING THE SEAT &
BACKREST STRUCTURE.-
Loosen off knob (54) by turning it
anticlockwise a few turns, Fig.12, and
pull the knob outward. Insert the seat
support (19) onto the post sticking out
of the main support (1), Fig.12.
Line up one of the height setting
holes, Fig.12, on the seat support and
release the knob then tighten the knob
(54) by turning it clockwise.
15.-
Position the backrest (17) on the
main body (5), Fig.12. Insert screw
(98), along with washers (123) and
locknut (127), and tighten securely.
16.- FITTING THE LEG SUPPORT.-
Take the leg support (18), fit the
spacer on the inside of the bushing for
the leg support, Fig.12.
Fit it into the holes on the front support
(3) and by lining up the holes insert
screws (110) along with the washers
(124) and secure using two spanners.
17.- FITTING THE
BUTTERFLY ARM SUPPORT.-
Fit the butterfly arm support (9) onto
the main body (5), Fig.13. Insert
screws (101), along with washers
(121) and nuts (126), and tighten
securely.
18.-
Take cable (68) and mount the
pulley (C) on the bracket (47) for the
top cable (66), as shown in Fig.13,
using screw (108) along with the
washer (121) and nut (126) and
tigthen.
Then mount pulleys (B and D) onto
the main support (1) Fig.13, fit the
cable exit covers and attach using
screws (99), along with the washers
(121) and tighten using nuts (126).
Do the same as described above for
pulleys (A and E), Fig.13.
19.- FITTING THE CHEST &
TRICEP SUPPORT.-
First, position the top right side panel
(34) on the main body (7), Fig.14.
Содержание TTPro G156
