10
ASSEMBLY INSTRUCTIONS.-
1
Take the unit out of its box and
make sure that all of the pieces are
there, Fig.1:
(17) Main body; (6) handlebar stem;
(19) Saddle post; (42) Saddle height
adjustment knob; (14) Stabiliser bar
with wheels; (18) Stabiliser bar with
adjustable blocks; (22) Saddle; (15R)
and (15L) Pedals; (1) Monitor; (2)
Handlebar; Bag of screws containing:
(27) Star washers; (24) Spacer bush;
(26) Allen screws; (13) Bolts M-8x70;
(28) Flat washers; (16) Cap nuts M-8;
(25) Handlebar clamping knob; (29)
Handlebar clamp; (23) Handlebar
guard; Spanners.
2
Take the stabiliser bar (18) with
adjustable blocks (64) and position it
on the stand at the rear of the
machine, as shown in Fig.2, and insert
bolts (13), fit the flat washers (10) and
the nuts (16), tighten securely.
Take the stabiliser bar with wheels
(14) and position it so that the two red
dots (X) line up, as shown in Fig.2A,
insert bolts (13), fit the flat washers
(10) and the nuts (16), tighten
securely.
3 FITTING THE HANDLEBAR
STEM.-
Take the screws (8) out of the main
body (17), bring the main post (6) up
to the boss on the main body, Fig.3,
and connect terminals (12) and (9)
Fig.3A. Insert the tip of the cable
sheath into the cable tension control
support (11), as shown in Fig.3B, pull
the sheath (5) up slightly and insert it
into the slot, see Fig.3C, then fit the
main mast onto the boss on the main
body, Fig.3, taking care not to pinch
the cables and make sure that the
tensioning control (5) Fig.6 operates
correctly.
Put bolts (8), along with their washers
(7) back in, Fig.3, making sure that the
handlebar is straight and then tighten
securely.
4
ATTACHING THE PEDALS.-
The assembly instructions for the
pedals must be followed to the
letter, fitting these incorrectly could
damage the screw thread on the
pedal or the crank.
Right and left refer to the position that
the user adopts when sitting on the
saddle to do the exercises.
The right-hand pedal (15R), marked
with the letter (R), screws onto the
right-hand crank, also marked with an
(R), in a clockwise direction. Tighten
securely, Fig.3.
The left-hand pedal (15L), marked
with the letter (L), screws onto the left-
hand crank, also marked with an (L),
in an anti-clockwise direction. Tighten
securely, Fig.3.
Once the pedals have been fitted,
insert the end of the pedal clip (1)
Fig.4 into the slot on the pedal (2)
adjusting it to your footwear on the
ledge of the pedal (3).
5
ATTACHING THE SADDLE.-
Place the saddle (22) Fig.5, onto the
saddle post (19), as shown in Fig.5,
bearing in mind that the holes on the
saddle post go at the front section of
the saddle, position the saddle
correctly and tighten nuts (Z) securely.
Now insert the saddle post into the
hole on the main body (17) Fig.6, fit
the saddle post knob (42) and adjust
the height of the saddle and tighten it
into position by turning the saddle post
knob (42) clockwise.
Содержание H6935
Страница 2: ...2 Fig 1 Fig 2 Fig 3 ...
Страница 3: ...3 Fig 3A Fig 3B Fig 3C Fig 4 Fig 5 Fig 6 Fig 7 ...
Страница 4: ...4 Fig 8 Fig 9 Fig 10 Fig 11 ...
Страница 32: ...32 H6935 ...