D812034 00100_03
12
- VISTA SW SXL
INSTALLATION MANUAL
12) OPERATING PARAMETER MANAGEMENT - DISPLAY
PARAMETER
DEFINITION
MIN. MAX. DEFAULT
CUSTOM
DESCRIPTION
01
Opening speed [°/s]
20
70
60
Motor speed during opening
02
Closing speed [°/s]
10
40
20
Motor speed during closing
03
TCA [s]
0
60
0
Waiting time before automatic closing.
04
Disabled hold time [s]
5
60
5
Waiting time before automatic closing using the disabled opening command
or in Low Energy mode
05
VISTA SW SXL:
Spring-operated
closing speed
1
9
5
Spring-operated closing speed (1=minimum speed, 9=maximum speed)
VISTA SW MXL:
Wind protection with
door closed
0
9
0
Sets wind protection strength with door closed
(0=wind protection disabled, 9=max. wind protection)
06
Opening force and
Closing force
1
9
5
Force exerted by leaf during opening and closing before obstacle alarm is
generated. (1=most sensitive; 9=least sensitive)
07
Acceleration and
Deceleration
5
30
30
Acceleration and deceleration speed
08
Approach angle
10
40
20
Adjusts approach angle (closing is 1/2 of opening)
09
Solenoid lock voltage
0
1
0
0 = 12Vdc solenoid lock output
1 = 24Vdc solenoid lock output
10
Solenoid lock type
0
6
0
0 = Not used
1 = Pulse mode with relock when door closes again
2 =
Standard magnetic (maglock)
N.B. Maglocks can be supplied only with 24V, set the “Solenoid lock
voltage” parameter to 24V.
3 = Fail-safe magnetic
4 = Motorized
5 = Pulse mode with relock when power is cut off
6 =
maglock with activation delay while closing
N.B. Maglocks can be supplied only with 24V, set the “Solenoid lock
voltage” parameter to 24V.
11
Solenoid lock
management time
Opening delay after lock
release
0
9
2
The time depends on the solenoid lock type:
- Pulse mode with relock when door closes again 50-500 ms
- Magnetic & Fail-safe 200 to 2000 ms
- Motorized 500 to 5000 ms
- Pulse mode with relock when power is cut off 100-1000 ms
12
Closing limit switch
pressure
0
9
5
Force exerted by the leaf to allow lock to engage
13
Single/Master/Slave
0
2
0
0 = Single board
1 = Board connected as Master
2 = Board connected as Slave
14
Door locked closed with
motor and lock
0
3
3
0 = Disabled
1 = Enabled with “Internal radar” mode
2 = Enabled with “Standard radar” mode
3 = Enabled with “Internal radar” and “Standard radar” mode
15
Auxiliary input 1
configuration
0
12
0
0 = Input configured as Disabled opening
1 = Input configured as Emergency opening
2 = Input configured as Interlock door with priority
3 = Input configured as Interlock door without priority
4 = Input configured as Lock Release Feedback
5 = Input configured as Lock release
6 = Input configured as Single Command with Master/Slave operating mode
7 = Input configured as Standby. If activated, it sets the door to standby only
with the door in the closed position.
8 = Input configured as wake up from Standby. If activated, it restores
operation following a Standby
9 = Input configured as step-by-step command, meaning that with a pulse
the door opens and stays open, standing by for another pulse to close, again
with the use of Int. Radar or Ext. Radar
10 = input configured as Temporary Stand By. If activated, the door is in stand
by and therefore the closing movement is spring-loaded. If deactivated, the
door works normally.
11 = Input configured as manual operation. If active, the operation of the
selector in the head is disabled.
12 = Input configured as Stop Closed operation. If active, the operation of the
selector in the head is disabled.
