manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard Quantum Series, Инструкция по эксплуатации и перечень запасных частей, Страница: 64 / 134

Поделиться
Скачать
BETTCHER INDUSTRIES Whizard Quantum Series Скачать руководство пользователя страница 64

Maintenance

5-22

Maintenance

Manual No. 101300

Operating Instructions and Parts List for the Whizard

 

Quantum

®

 Trimmer

March 16, 2015

ASSEMBLY OF HANDPIECE (CONTINUED)

Blade Installation (Continued)

•

Adjust the housing for proper running clearance. The blade should turn freely with a slight 
side-to-side motion. This leaves room for the grease

WARNING!

 Make certain that the blade is free to rotate in the housing. If the blade does not 

turn freely, it may cause the tool to rotate in the hand.

•

Tighten the left cover screw to 35 in-lb. (4 N-m). Use of the Bettcher torque wrench kit is 
recommended. 

Refer to Section 7, Tools.

•

Re-check the running clearance.

Blade is too tight

•

If the blade is too tight in the housing, adjustments can be made by loosening the left cover 
retaining screw and slightly spreading open the housing. 

•

Check the housing for proper running clearance and retighten the left cover screw to 35 
in-lb. (4 N-m). Use of the Bettcher

®

 torque wrench kit is recommended. 

Refer to Section 7, 

Tools.

COMPANY 

CONFIDENTIAL

Содержание Whizard Quantum Series







































































































































Отзывы:

Нет отзывов