BETTCHER INDUSTRIES Whizard Quantum Series Скачать руководство пользователя страница 36

Страница: 36 / 134

Instructions for Operation

4-4

Instructions for Operation

Manual No. 101300

Operating Instructions and Parts List for the Whizard Quantum

Trimmer

January 16, 2015

STEELING THE BLADE

Use the Whizard Special Steel anytime you feel the edge of the blade needs to be raised for better
cutting action.

Steeling For Model Q360, Q505, Q625, Q850, Q880, Q1850, Q1880,
Q1000, Q1300, Q1400 and Q1500

Use the Whizard

Special Steel against the flat ground surface on the outside surface of the

blade. Be sure to hold the "steel" flat and across the centerline of the blade to prevent "rounding
off" or rolling of the edge.

The INSIDE edge of the blade should be steeled only with the Special Steeling Device mounted
on the inside diameter of the blade housing. This is accomplished as follows:

•

Hold the Whizard Special Steel on the bottom edge of the blade and the handpiece in your
normal operating hand with the blade down, or away from you.

•

With your thumb, lightly push down on the push button of the steeling device.

DO NOT

hold the steeling device against the rotating blade steadily, but rather lightly contact the
blade edge.

Replace or sharpen the blade if this procedure does not improve the cutting action.

WHIZARD® SPECIAL STEEL

AND PUSH BUTTON

WHIZARD® SPECIAL STEEL

AND PUSH BUTTON

WHIZARD® SPECIAL STEEL

COMPANY

CONFIDENTIAL

Содержание Whizard Quantum Series







































































































































Результаты поиска

Содержание Whizard Quantum Series

Отзывы:

BETTCHER INDUSTRIES Whizard Quantum Series, Инструкция по эксплуатации и перечень запасных частей, Страница: 36 / 134

Результаты поиска

Содержание Whizard Quantum Series

Отзывы: