manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard Quantum Series, Инструкция по эксплуатации и перечень запасных частей, Страница: 48 / 134

Поделиться
Скачать
BETTCHER INDUSTRIES Whizard Quantum Series Скачать руководство пользователя страница 48

Maintenance

5-6

Maintenance

Manual No. 101300

Operating Instructions and Parts List for the Whizard

 

Quantum

®

 Trimmer

March 16, 2015

DISASSEMBLY OF HANDPIECE

Remove the Blade Housing and Cover Plate

•

Loosen cover retaining screws until the 
cover is free.

NOTE:

 The screws will stay in the frame. 

•

Remove the blade housing.

•

Pull the pinion out of the frame.

Remove the Optional Depth Gauge / Disc Gauge from the Cover 
Plate

•

Loosen the two attachment screws located inside the depth gauge. It is not necessary to 
remove the screws.

•

Slide the gauge upward until the depth gauge clamps come out of the cover plate grooves.

 

 

 

 

 

ATTACHMENT

SCREWS (2)

ADJUSTMENT KNOB

DEPTH / DISC GAUGE

ATTACHMENT
SCREWS

COMPANY 

CONFIDENTIAL

Содержание Whizard Quantum Series







































































































































Отзывы:

Нет отзывов