BETTCHER INDUSTRIES Quantum Flex 1000 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 118

background image

Unpacking and Installation

3-4

Unpacking and Installation

Manual No. 107013

Operating Instructions and Parts List for the Quantum Flex

™

Trimmer

January 1, 2018

OPTIONAL THUMB SUPPORT AND HANDLE ADJUSTMENT

Your Quantum Flex

™

Trimmer has been supplied with a spacer ring or optional thumb support. If

using the optional thumb support, the operator's thumb should be fully supported and rest
comfortably in the support. The thumb support has been optimized to fit most hands comfortably.

Fitting the correct size handle to the grip of an operator's hand is a very important step when
trying to reduce risks associated with cumulative trauma disorders.

NOTE:

S,M,L markings on

handle.

Here is a very simple procedure to determine correct handle size:

STEP 1 - Assemble three (3) knives each with a different size handle.

STEP 2 - Allow the user to hold the knife and apply the grip pressure normally used during the
job operation.

NOTE

:

If the operator normally wears a glove, this process should be done with all the gloves

used in normal operation.

The operator should choose the handle that is most comfortable. Allow the operator to work with
this handle on a tool for several days. If the operator is not comfortable with the handle selection,
allow the operator to try a different size.

«
...
18
19
20
21
22
...
»

Содержание Quantum Flex 1000























































































































Отзывы:

Нет отзывов

Похожие инструкции для Quantum Flex 1000

Бренд: Laica Страницы: 4

Бренд: Panasonic Страницы: 30

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: XanLite Страницы: 2

Бренд: X-Rite Страницы: 6

REBOUND DUAL ST

Бренд: Össur Страницы: 104

Бренд: Össur Страницы: 130

Бренд: EFX Страницы: 2

Heart Guardian AED

Бренд: Radian Страницы: 36

UltraVent XS Plus 6 2/3 E

Бренд: Rational Страницы: 220

Бренд: Ebyte Страницы: 7

Бренд: Vitax Страницы: 12

Бренд: ZAMST Страницы: 14

Бренд: Hatco Страницы: 24

Бренд: LifeSpan Страницы: 8

Бренд: Vicon Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды