BETTCHER INDUSTRIES Quantum Flex 1000 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 118

background image

Safety

1-2

Safety

Manual No. 107013

Operating Instructions and Parts List for the Quantum Flex

®

Trimmer

January 1, 2018

SIGNAL WORDS & SIGNAL WORD PANELS

The signal word definitions provided, comply with the American National Standard for Product Safety

Information in Product Manuals, Instructions, and Other Collateral Materials (ANSI Z535.6-2011).

This technical manual is printed in black and white.

DANGER

Indicates a hazardous situation that, if not avoided, will result in death or
serious injury.
(The signal word Danger is in white letters on a safety red background)

WARNING

Indicates a hazardous situation that, if not avoided, could result in death
or serious injury.
(The signal word WARNING is in black letters on a safety orange
background)

CAUTION

Indicates a hazardous situation that, if not avoided, could result in minor
or moderate injury.
(The signal word CAUTION is in black letters on a safety yellow
background)

NOTICE

Indicates information considered important, but not hazard-related (e.g.
messages relating to property damage).
(The signal word NOTICE is in italicized, white letters on a safety blue
background)

«
...
4
5
6
7
8
...
»

Содержание Quantum Flex 1000























































































































Отзывы:

Нет отзывов

Похожие инструкции для Quantum Flex 1000

Бренд: Baker Instrument Company Страницы: 24

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Raymarine Страницы: 90

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: Zero Hand Truck Страницы: 38

Бренд: XM Fitness Страницы: 10

Бренд: ParaBody Страницы: 3

Бренд: hager Страницы: 2

Бренд: Hantek Страницы: 124

Бренд: OAKWORKS Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: Oakton Страницы: 2

Бренд: O2matic Страницы: 4

MIAMI J ADVANCED

Бренд: Össur Страницы: 35

Бренд: Össur Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды