manualshive.com logo in svg

BETTCHER INDUSTRIES AirShirz, Инструкция по эксплуатации и список запасных частей

Поделиться
Скачать
BETTCHER INDUSTRIES AirShirz Скачать руководство пользователя страница 71

OPERATING  

BETTCHER  

   AIRSHIRZ

®

 

INSTRUCTIONS 

              INDUSTRIES, INC.                                    Rev.  September 24, 2016

 

Page 65 

9.4.13.1  Single Power Cylinder Disassembly & Repair    (Continued) 

 

Pull power cylinder rod fully outward and thoroughly clean its surface. 
 
Remove the four (4) flat head screws from the side of the power cylinder. 
 
Temporarily put a clevis pin into the rod bearing to act as a gripping handle.  Be sure to work over 
a table to catch loose parts.  While holding the body of the power cylinder in one hand, pull 
outward on the rod with other hand until the front end of the  power cylinder comes out.  

Never 

Grasp Rod with a Tool as Any Nicks Will Destroy it

! 

 
Set aside clevis pin and the wear strip which fell out of rear piston groove. 
 

Further Disassembly Is Recommended Only As Needed. 
 

Clean the rod and make sure it is free of dirt or burrs.  Check that there are no sharp edges at the 
cross-hole.  (If the cross-hole edges are sharp, the piston will need to be removed from the rod, so 
the rod can be pulled out of the base from the front.   Otherwise, the lip seal may be damaged).  
Apply a thin coat of Bettcher

®

 Max-Z-Lube, then slowly slide it and the piston, out of the base. 

 
Examine all seals: 
 

•

 

O-rings with a wide flat band, pinch marks, cracks or nicks should be replaced. Remove 
defective O-ring.  Clean the groove.  Apply Bettcher

®

  Max-Z-Lube  to new O-ring and 

install into groove. 

 

•

 

The lip seal for the rod should be replaced if air had  been leaking from the rod, if it was 
removed, or if the inner lip appears uneven or worn.  Use tweezers or a small wire to pry 
lip seal inward and pull it out from the inside of the base.  Clean the groove between base 
and bearing.  Apply Bettcher

®

  Max-Z-Lube  all over the new seal and squeeze it into the 

base from the same side it was removed.  Use a blunt object to coax it into position.  Be 
sure that the lip is facing toward the inside of the base as shown in Figure #63. 

 

 

FIGURE #63 

Lip Seal 

Base 

Wiper 

.239 (6.07mm) 

Содержание AirShirz















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды