BETCO Stealth ASD20BT Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 68

BETCO Stealth ASD20BT Скачать руководство пользователя страница 13

13

1. MACHINE OPERATION

A. Connect the battery plug to the machine plug.

B. Turn the key (

1

) of the main switch to the "ON" position (clockwise). The bat-

tery charge level indicator lights will immediately come on.

C. Turn on the water valve (

2

) (the water dispenses automatically when the

brush is turning).

D. Release the foot lever (

3

) and lower the brush deck.

E. Lower the squeegee by rotating the squeegee lift handle (

4

) counter clock-

wise. The vacuum motor will turn on.

F. Check that the brake (

5

) is released.

G. Pulling the switch levers (

1

), activates the brush and the machine begins to

move. During the first few feet, check that the amount of solution dispensed

is correct, and that the squeegee dries the floor.

H. The machine will now start to scrub and dry until the solution tank is empty

or recovery tank is full.

OPERATION

«
...
11
12
13
14
15
...
»

Содержание Stealth ASD20BT





































































Отзывы:

Нет отзывов