background image

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Instruction Manual

Reflow-Controller

Page 2 of 14

2.  Safety Information 

2.1. 

Intended use 

This product may only be used in the control of a Reflow Oven. 

Any usage of this product other than that described above is likely to lead to 

damage including short-circuiting, fire, electric shocks etc. It is forbidden to alter 

and/or convert the entire product in any way. 

This product fulfills the legal, national and European requirements. All company 

names and product designs are registered trademarks of the respective owners. 

All rights reserved. 

Acquaint yourself with the operating instructions of the CONTROLLER, which you 

will find on the CD supplied with the Reflow oven. 

 

2.2. 

Safety Instructions 

Any damage caused by neglect of the operating instructions renders any 

guarantee/warranty null and void! We accept no liability for any damages so 

caused! 

We accept no liability for any special or personal injuries caused by inappropriate 

handling or neglect of the safety instructions. In such cases the 

warranty/guarantee is null and void. 

• 

For safety and copyright (EU) reasons no arbitrary changes or alterations to 

the product are permitted. Never disassemble the unit! 

• 

The product is designed for operation through the mains supply only 

(230V~/50Hz). Must be properly earthed. Connect the CONTROLLER to a 

socket using the supplied protected plug only. 

• 

This product is not a toy and is not intended for use by children. Operate the 

product out of the reach of children, same goes for storage. Children may 

attempt to insert items into the openings on the unit, risking a lethal electric 

shock! 

• 

The product is suitable for dry conditions only, do not allow it to become damp 

or wet. Never operate the product outdoors or in humid conditions, never 

touch it with damp or wet hands! Danger of lethal electric shock! 

• 

The product should not be operated unsupervised. 

Содержание Reflow

















Отзывы: