manualshive.com logo in svg

Bestop PowerBoard 75152-15, Руководство по установке, Страница: 9 / 15

Поделиться
Скачать
Bestop PowerBoard 75152-15 Скачать руководство пользователя страница 9

P9 - 75152  Rev. C  0416

Installation Instructions - PowerBoard

®

© 2016 Bestop, Inc.

Page 9

Section 5

Install Idler Linkages and Linkage Motors

Hardware

#M6-1.0 x 35

Socket Cap Screws

Part # 460.95

Qty. 3 per linkage

#M6 Flat Washer

Part # 481.96

Qty. 3 per linkage

#M8-1.25 x 20

Button Head Screw

Part # 473.83

Qty. 2 per Linkage

#M8-1.25 x 25

Button Head Screw

Part # 522.95

Qty. 1 per Linkage

Step 2

2

1

Enlarge this hole 

in the welded

body flange to

3/8” diameter

3

4

Step 1

Step 2

Attach a Motor to each Motor Linkage using three 

#M6-1.0x35 Socket Cap Screws, with three #M6  

Flat Washers.
Left (Driver) side motor linkage shown above.  

Repeat for Right (Passenger) side of the vehicle.
With the Motor-Linkage assembly near the vehicle 

mounting position - underneath the rear of the  

vehicle door opening - attach the wiring harness  

motor connector to the motor.
Repeat on the Right (Passenger) side of the vehicle.

Step 1

Step 2

Motor Linkage - Left

Driver Side

Part #517.89

Qty. 1

Motor

Part #496.12

Wiring harness

motor connector

The Idler Linkage mounts toward the front of the 

vehicle. Left (driver) side shown.

 1   Enlarge the small hole as shown to 3/8” dia.
 2   Mount the Idler Linkage behind the welded body 

flange using  3   two #M8-1.25x25 Button Head 

Screws with #M8 Flat Washers.
 4   Install one #M8-1.25x25 Button Head Screw  

with #M8 Flat Washer through the bottom of the  

Idler Linkage into the bottom of the vehicle body.

             

WARNING

   Only tighten the screws 

holding the Idler Linkages to the vehicle finger tight 

at this time.

Motor Linkage - Left

Driver Side

Part #525.19

Qty. 1

#M8 Flat Washer

Part #470.05

Qty. 3 per Linkage

Содержание PowerBoard 75152-15
















Отзывы:

Нет отзывов