background image

Installation Instructions

PowerBoard

®

Automatic Retracting Running Board

Vehicle Application:

Jeep Wrangler Unlimited

2007- 2016

Part Number 75152-15

Installation Instructions - PowerBoard

®

© 2016 Bestop, Inc.

P1 - 75152  Rev. C  0416

   

 

    

   

 

 

WARNING

Read and follow, precisely, all installation instructions provided when 

installing this product. Failure to do so may result in a poor fit, and could 

place occupants of the vehicle in a potentially dangerous situation.

WARNING

WARNING

 

 

 

The manufacturer strongly recommends that this product be 

professionally installed.

 

 

 

Failure to carefully follow the electrical installation steps  

could result in severe electrical shock which could harm the installer and/or damage 

the vehicle.

 

 

 

This product is designed primarily to enhance the appearance 

and comfort of the vehicle. Do not rely in any way on the components of this product  

to protect the occupants within the vehicle, or to protect against injury or death in  

the event of an accident. Never operate the vehicle in excess of manufacturer’s  

specifications.

Installation Tips

WEAR SEAT BELTS AT ALL TIMES

Support

Installation Time

Tools

Skill Level

4 Hours

4 - Difficult

We’re here to help!

Gto to 

http://www.Bestop.com

and click “Ask a Question”

Safety Glasses

1/8” Drill

3/8” Drill

5mm Allen Wrench

10mm Wrench

Drill-Driver

Содержание PowerBoard 75152-15
















Отзывы: