Besantek BST-GFL31 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 33

background image

BST-GFL31 User Manual

29

resistance become 0. Current value is around 2.7mA.
For testing of voltage, resistance and current, please refer to “2.4 Set Generator Output Signal”.

Note

: To ensure the security of equipment, please DO NOT output higher voltage for short-circuit.

3)

Check if signal receiver is normal
When signal generator is short-circuited, set the same receiving frequency in receiver (10Hz), set
frequency synchronization and set reference point.
Normally after frequency synchronization, phase angle and signal strength are pretty stable. After
reference setting, signal strength becomes 100%, phase angle is around 0° and current direction
will be . If current detector is clamp on the opposite direction, phase angle will become around
180° and direction will be reverse

.

4.2 FAQ

Item

Description

Causes

Solutions

1

Signal strength and

phase angle in signal
receiver sometimes is
high sometimes low

1. Signal display of signal
generator is set as
“Discontinue” mode.

Change it to “Continue” mode.

2. Signal is too weak

Increase the output voltage
somehow

3. There might be similar
frequencies around that
interferes the signal

Use frequency spectrum analyzing
function of signal receiver to test
surrounding signals and select the
right output frequency.

4. Opening jaw of current
detector is closed or the jaw
has dirt.

Close the jaw of current detector

and clean the clamp jaw.

5. Reference value is set
when it does not clamp in the
circuit that has current flow.

Clamp the current detector in the
circuit and make sure that the
signal generator is transmitting
signal properly, then set the
reference point.

2

In the same point,

signal receiver
shows steady signal
strength but phase
angle is increased or
decreased in certain
rate.

1. Frequency synchronization

is not done in the signal
receiver.

2. Current detector is not

kept stable during
frequency synchronization.

Redo “Frequency synchronization”
with current detector clamped on
red testing lead.

3

Relay maloperation
during ground fault
location

Red test lead is incorrectly
connected with busbar that
has normal insulation.

Connect it in the right busbar

4

Equipment works for
short time. Battery
power off pretty soon.

Not fully powered before
operation

1. Fully charge the signal generator
and receiver before using.
2. For long time operation, please
connect power adaptor with signal
generator.

«
...
30
31
32
33
»

Содержание BST-GFL31


































Отзывы:

Нет отзывов

Похожие инструкции для BST-GFL31

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: Fenton Страницы: 16

Бренд: Labelmate Страницы: 61

Бренд: Labconco Страницы: 62

Бренд: RAPID REBOOT Страницы: 18

Бренд: MacDon Страницы: 170

Бренд: MacDon Страницы: 108

Бренд: MacDon Страницы: 108

Бренд: MacDon Страницы: 51

Бренд: MacDon Страницы: 104

Бренд: MacDon Страницы: 240

QUANTOFIX Relax

Бренд: Macherey-Nagel Страницы: 192

Бренд: MacDon Страницы: 182

Бренд: MacDon Страницы: 192

Бренд: MacDon Страницы: 53

Бренд: MacDon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды