Bernini Be42, Руководство пользователя, Страница: 17 / 28

Be42 OEM's Manual V5.0.XX - December - 2010 page 17
17
Table 7.09 - Output Options Table
Option & description Option & description
[ 0 ] Output is disabled [32] Alarm form Input 2: Shutdown/Warning
[ 1 ] Under Frequency Shutdown [33] Alarm form Input 3: Shutdown/Warning
[ 2 ] Over Frequency Shutdown [34] Alarm form Input 4: Shutdown/Warning
[ 3 ] Over Current Shutdown [35] Cumulative Oil Alarms
[ 4 ] Over Current Warning [36] Cumulative Temperature Alarms
[ 5 ]
Overload Warning or Shutdown
(^^^)
[37] Cumulative Alternator Alarms
[ 6 ] Over Voltage Shutdown [38] Common Fuel Alarms
[ 7 ] Under Voltage Shutdown [39] Horn Output (See table 7.05 [P50])
[ 8 ] Alternator Failure Shutdown [40] Crank Delay (Start Warning)
[ 9 ] Low Oil Pressure Warning [41] Presence of Nominal Mains Parameters
[10] Low Oil Pressure Shutdown [42] Mains Failure Timing
[11] Oil Sender Failure Warning [43] Mains Restore Timing
[12] High Temperature Warning [44] KG Status
[13] Temperature Switch Shutdown [45] KM Status
[14] Temperature Sender Failure Warning [46] Pre-glow MODE 1/2/3/4
[15] Low Battery Voltage Warning [47] PURGE (gas engine valve control)
[16] High Battery Voltage Warning [48] RENT<48h
[17] Low Fuel Shutdown (switch) [49] RENT=0h (Expired)
[18] Fuel Low Warning (sensor) [50] Engine Running Status
[19] Fuel Reserve Warning (switch) [51] Presence of Nominal Generator Voltage
[20] Fuel high Warning (sensor) [52] BE42 in OFF MODE (Status)
[21] Fuel Sender Failure Warning [53] BE42 in MANUAL MODE (Status)
[22] Emergency Stop Shutdown (Er08) [54] BE42 in AUTO MODE (Status)
[23] Stop Pushbutton Used in AUTO (Er09) [55] BE42 in TEST MODE (Status)
[24] Maintenance SERVICE 1 (Er10) [56] BE42 in LOCK MODE (Status)
[25] Maintenance SERVICE 2 (Er10) [57] Be42 runs the Automatic Periodic Test
[26] Maintenance SERVICE 3 (Er10) [58] Cooling Timing
[27] Engine Belt Break Shutdown [59] Warm up Timing
[28] Fail To START Shutdown [60] Cycling mode (Logical OR of engine running
and stop solenoid)
[29] Fail To STOP Shutdown [61] Start Pilot repeat output (it repeats the crank
output terminal #9)
[30] Indication of Parameter Error warning - --
[31] Alarm form Input 1: Shutdown/Warning - --
(^^^) If an input is configured with option [20] or [21] (see table 7.07)
Table 7.10 - Oil Pressure Sensor Settings
Display Parameter Default
Range
[Pr.1] Pressure [ 0.0] Bar 0 up to 20 Bar
0 up to 2000
Ohm
[-r1-] Resistance [ 10] Ohm
[Pr.2] Pressure [ 2.0] Bar
[-r2-] Resistance [ 51] Ohm
[Pr.3] Pressure [ 4.0] Bar
[-r3-] Resistance [ 86] Ohm
[Pr.4] Pressure [ 6.0] Bar
[-r4-] Resistance [ 122] Ohm
[Pr.5] Pressure [ 8.0] Bar
[-r5-] Resistance [ 152] Ohm
[Pr.6] Pressure [ 10.0] Bar
[-r6-] Resistance [ 180] Ohm