Be242 Be242RB OEM's Manual V3.X.XX -
January - 2021 page 2
2
Alphabetic index
Alternator Failure E04 ..... 7.02B
[P.15]
Alarms .............................. 4.10, 8.0
Alarm output control ....... 7.09,
[39]
Alarm inputs .................... 7.06, 8.0
Automatic ......................... 2.3
Battery, Alarms ................ 4.10
[Er.13]
Belt break ........................ 4.10
[Er.02]
Choke, control ................. Table 7.03
[P.22]
Characteristics ................. 14.0
Charger Alternator ........... 11.0, 7.03
[P.26]
Clear the memory ............ 12.3
Contactors ........................ 2.21, 18.0
Connectors, Plugs ........... 19.0
Crank timing .................... 7.03A
[P.19]
Current Transformer ....... 7.02B
[P.18]
Cooling down time .......... 7.03A
[P.24]
Defaults ............................ 6.20
Dimensions ...................... 19.0
Display ............................. 3.0
Display Messages ........... 4.10, 4.20
Er.0--8.. Error codes ........ 4.10
[FAIL] Memory error ........ 4.10 [FAIL]
Engine Running ............... 11.0
Emergency input ............. 4.10
[Er.08]
Events .............................. 4.30
Fail to Start ...................... 4.10
[Er.11], P.34
Fail to Stop ....................... 4.10
[Er.07]
Front Panel ...................... 1.0 Figure 1
Frequency ........................ 7.02A
[P.11][P.12]
Fuel Level ......................... 7.04
[P.36 - - 38]
Generator Voltage ........... 7.02
[P.9]
[P.10]
Generator Frequency ...... 7.02
[P.11]
[P.12]
Generator Failure E04 ..... 7.02B
[P.15]
Glow Plugs ....................... 7.03
[P.22]
Hi-U, Over Voltage ........... 7.02A
[P.10]
Hour Counter ................... 9.0
Horn Programming .......... 7.05
[P.50]
Inputs (Programmable) ... 7.06, 7.07
LED, LEDs ........................ 5.0, 2,21, 2.3
Lamp Test ........................ 5.1
Lo-U, Under Voltage ........ 7.02A [P.09]
Lock, Remote Lock E03 .. 4.10
Low Battery voltage ........ 4.10,[Er.13]
Log Events.........................4.30
Mains Failure ................... 7.01A
[P.01]
Mains Restore .................. 7.01B
[P.02]
Maintenance timers ......... 7.05, 16.40
Mains Simulation ............. 7.07 [15]
Measurements .................... 3.0
Memory clear ...................... 12.3
Memory Events ................... 4.30
Messages (Display) ............ 4.0
Manual................................. 2.2
Outputs (programmable) ... 7.09
Operation modes ................ 2.0
Overload ............................. 4.10 [Er.05]
Overload (external)............. 7.07 [20][21]
Over Frequency .................. 4.10 [Er.01]
Over Voltage HI-U ............... 4.10 [HI-U]
Parameters ......................... 7.0
Password ............................ 6.40
Parameters reading ............ 6.30
Periodic test........................ 7.05 [P.41][P.42]
Program, Programming ..... 6.0
Pre Glow ............................. 7.03[P.22]
Pump Set control ............... 10.0
Power Supply ..................... 14.0
Push buttons ...................... 2.0, 2.2
Rest time ............................. 7.03A [P.21]
Rental Programming .......... 7.05 [P.47]
R.P.M...................................7.02B [P.16]
Settings (Parameters) ........ 7.0
Service timers ..................... 7.05, 16.40
Single Phase operation ...... 16.30
Specifications ..................... 14.0
Start ..................................... 2.2
Start Attempts .................... 7.03B [P.31]
Starting Failure ................... 4.10 [Er.11]
Stop, Stop solenoid ............ 7.03A [P.25]
Temperature ....................... 7.03B [P.30]
Terminal description .......... 19.0
Test, Remote Test ............. 7.07 [10] [11]
Test mode .......................... 2.4
Test timeout ....................... 16.60
Transformer, Current ......... 7.02B [P.18]
Troubleshooting ................. 13.0
Under Voltage Lo-U ............ 7.02A [P.09]
Under Frequency ................ 7.02A [P.11]
Voltage measurements ...... 3.0
Warm-Up time ..................... 7.03A [P.23]
Wiring diagram ................... 18.0
