Berner 175035, Оригинальное руководство пользователя

Страница: 18 / 197

English - 3
and any other condition that may affect the
power tools operation. If damaged, have the
power tool repaired before use.
Many acci-
dents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g)
Use the power tool, accessories and tool bits
etc., in accordance with these instructions
and in the manner intended for the particular
type of power tool, taking into account the
working conditions and the work to be perfor-
med.
Use of the power tool for operations
different from those intended could result in
a hazardous situation.
5) Service
a)
Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts.
This will ensure that the safety of
the power tool is maintained.
Safety warnings common for sanding with
sanding discs, working with wire brushes
and polishing
This power tool is to be used as a sander, wire
brush and polisher. Read all safety warnings,
instructions, illustrations and specifications provi-
ded with this power tool.
Failure to follow all
instructions listed below may result in electric
shock, fire and/or serious injury.
Operations such as grinding or cutting-off are not
recommended to be performed with this power
tool.
Operations for which the power tool was
not designed may create a hazard and cause per-
sonal injury.
Do not use accessories which are not specifically
designed and recommended by the tool manufactu-
rer.
Just because the accessory can be attached to
your power tool, it does not assure safe operation.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Accessories running faster than their rated
speed can break and fly apart.
The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool.
Incorrectly sized accessories
cannot be adequately guarded or controlled.
The arbor size of wheels, flanges, backing pads or
any other accessory must properly fit the spindle
of the power tool.
Accessories with arbor holes
that do not match the mounting hardware of the
power tool will run out of balance, vibrate
excessively and may cause loss of control.
Do not use a damaged accessory. Before each use
inspect the accessory such as abrasive wheels for
chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked
wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged
accessory. After inspecting and installing an
accessory, position yourself and bystanders away
from the plane of the rotating accessory and run
the power tool at maximum no-load speed for one
minute.
Damaged accessories will normally
break apart during this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and workshop apron
capable of stopping small abrasive or workpiece
fragments.
The eye protection must be capable
of stopping flying debris generated by various
operations. The dust mask or respirator must be
capable of filtrating particles generated by your
operation. Prolonged exposure to high intensity
noise may cause hearing loss.
Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear per-
sonal protective equipment.
Fragments of workpi-
ece or of a broken accessory may fly away and
cause injury beyond immediate area of operation.
Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a “live”
wire may make exposed metal parts of the
power tool “live” and shock the operator.
Position the cord clear of the spinning accessory.
If you lose control of the power tool, the cord
may be cut or snagged and your hand or arm
may be pulled into the spinning accessory.
Never lay the power tool down until the accessory
has come to a complete stop.
The spinning acces-
sory may grab the surface and pull the power
tool out of your control.
Do not run the power tool while carrying it at your
side.
Accidental contact with the spinning acces-
sory could snag your clothing, pulling the acces-
sory into your body.
Regularly clean the power tool’s air vents.
The
motor’s fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
3 41 01 188 06 0.book Seite 3 Mittwoch, 5. Dezember 2012 9:48 09