Berker RMD 75314013 Скачать руководство пользователя страница 17

Страница: 17 / 17

Shutter actuator 4gang 6A 230V manual
RMD
75314013

Technical

Documentation

Version: 10.05.2005

Page: 17 / 17

(Subject to prior change)

75314013.doc

Part 7

Manual control

enabled

disabled

In the manual control mode it is possible to
operate the output channels manually.
Manual control works only when mains
voltage is available.

Manual control can on principle be
activated.

The manual control mode cannot be
activated when bus voltage is available.

Manual control on bus
voltage failure

enabled

disabled

Manual control can additionally be
permitted in the event of bus voltage
failure.

The manual control mode can only be
activated in the event of bus voltage failure.

Manual control can, on principle, not be
activated.

Only with "Manual control" = "Inhibited"!

Software information

•

This type of actuator does not permit read-out of bus voltage by the ETS!

Содержание RMD 75314013


















Результаты поиска

Содержание RMD 75314013

Отзывы:

Похожие инструкции для RMD 75314013

Бренды по названию

Популярные бренды

Berker RMD 75314013, Техническая документация инструкция

Результаты поиска

Содержание RMD 75314013

Отзывы:

Похожие инструкции для RMD 75314013

Бренды по названию

Популярные бренды