manualshive.com logo in svg

Bergstrom NITE Phoenix, Руководство по установке, Страница: 14 / 67

Поделиться
Скачать
Bergstrom NITE Phoenix Скачать руководство пользователя страница 14

 

 

1-14 

Kenworth T600-T660-T800-W900 

 

 

 

 

 

 

 

 

               rev 10/7/13 

Installation Procedures 

Installation Procedures 

15 

B 

A 

Run Wiring behind 

NITE Phoenix

 

Duct.  

Loom the control harness.

 

Connect it to the back of the 
controller. Place the wiring harness 
along the channel on the back of the 
duct.  Secure wiring in channel with 
tape. The duct is now ready to be 
attached.

 

 
 
 
 
 
 
Attach stealth to the 

NITE Phoenix

 

Duct.

  After the controls are installed 

slide 

NITE Phoenix

 duct and wiring 

down through the slot in the decking 
enough to fasten the elbow to the duct 
using two 1″ X 5/16 self-tapping 
screws.  Seal around stealth with 
silicone sealant. Now raise duct back 
up to proper location. 
 

Attach 

NITE Phoenix

 Duct to Back 

Wall of Sleeper.

  Press the top of the 

duct up against the back wall. Make 
sure the duct is square and level 
against the back wall. Use 1″ X 5/16 
hex head self-tapping screws to attach 
top of duct to back wall. Place 3 - 5 
screws in each duct opening and install 
at different angles (A). Take care not 
to over tighten. Snap both louvers into 
place (B). 
 
 
 
 
 
 

14 

Содержание NITE Phoenix




































































Отзывы:

Нет отзывов