background image

4

Bentone  

1.  General Information

This Installation and Maintenance manual:

•  is to be regarded as part of the burner and must always be kept near 

the installation site

•  is intended for use by authorised personnel

•  must be read prior to installation

•   must be observed by all who work with the burner and associated 

system components

•  work with the burner may only be carried out by certifi ed installers/

personnel

Enertech AB is not liable for any typographical errors and reserves the right 
to make design changes without prior notice.

Safety instructions

•  The burner may only be used for its intended purpose in accordance 

with the product’s technical data.

•  The burner may only be installed and operated by authorised 

personnel.

•  The product is packaged to prevent damage from occurring during 

handling. Handle the product with care. Lifting equipment must be 
used to lift larger packages. 

•  The products must be transported/stored on a level surface in a dry 

environment, max. 80% relative humidity, no condensation. 
Temperature -20 to +60 °C.

•  Check that the burner is compatible with the boiler’s output range.

•  All components must be installed without being bent, twisted or 

subjected to mechanical or thermal forces which can affect the 
components.

•  The burner must be installed so that it complies with local regulations 

for fi re safety, electrical safety, and fuel distribution.

•  The gas outlet from the pressure regulator shall be confi gured in 

accordance with applicable regulations and lead to a safe area. 

•  Make sure when installing the equipment that there is enough space to 

service the burner.

•  Permitted temperature during operation -10 to +60 °C. Max 80% 

relative humidity, no condensation.

•  The installer must ensure that the room has adequate air supply.

•  The room must comply with local regulations pertaining to its intended 

use.

•  The installation site must be free of chemicals.

•  Burner pipes, fan wheels and air dampers may contain sharp edges.

•  The surface temperature of the burner’s components can exceed 60 

°C.

•  Caution: The burner has moving parts, and there is risk of crushing 

injuries.

172 515 01    2018-01-02

Содержание BG 650

















































Отзывы: