Benthos 865-A Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 68

background image

Model 865-A Deep Sea Acoustic Release/Transponder

M-855-009

Benthos, Inc.

29

j.

Check the voltage at points 1 and 2 with respect to ground (chassis), (see Figure 8-3). The
voltage at each point should be very close to 13.5 volts.

Battery Pack Connector P.C. Board

Figure 8-3

k.

Run the motor by turning the switch to "TEST-RETRACT". Notice that the voltage drops
slightly at points 1 and 2. This test verifies that both battery strings are supplying current.

l.

Return the switch to the HOLD-EXTEND position. Plug the electronic chassis back on and
secure it with two nuts, including the split and flat washers.

STEP 3 - LIGHTLY GREASE THE O-RINGS

a.

Inspect the face and radial sealing O-rings for damage. If necessary, see Section 8.7 of this
manual for replacement instructions.

b.

Using silicone grease, lightly grease the face and radial sealing O-rings. It is EXTREMELY
IMPORTANT that only a very thin coating of grease is used. Too much grease could displace
the O-ring when it is under pressure.

c.

Also, very lightly grease the metal face seal outside of the O-ring and on the end of the
housing. Use just a very thin film of grease here to prevent crevice corrosion.

STEP 4 - CLOSE THE HOUSING

a.

It is strongly recommended that the air inside the housing be very dry to prevent condensation
when the instrument is deployed. As the housing is being closed, purge the inside with dry
nitrogen gas, then quickly close the housing.

«
...
35
36
37
38
39
...
»

Содержание 865-A





































































Отзывы:

Нет отзывов

Похожие инструкции для 865-A

Бренд: Raytheon Страницы: 62

Бренд: Raytheon Страницы: 69

RCDC1 - IPOD/IPHONE ALARM CLOCK

Бренд: Panasonic Страницы: 2

Бренд: Garmin Страницы: 2

Бренд: Samyung ENC Страницы: 23

Бренд: JBL Страницы: 9

Бренд: TruTech Страницы: 13

Бренд: Sangean Страницы: 25

Бренд: Grundig Страницы: 14

Бренд: Coby Страницы: 1

Бренд: Sirius Satellite Radio Страницы: 36

Бренд: Eaton Страницы: 83

Бренд: Icom Страницы: 16

Бренд: Ocean Digital Страницы: 26

Бренд: LENCO Страницы: 91

Бренд: Vertex Standard Страницы: 5

Бренд: Vertex Standard Страницы: 5

Бренд: Sanyo Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды