Benthos 865-A Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 68

background image

Model 865-A Deep Sea Acoustic Release/Transponder

M-855-009

Benthos, Inc.

27

This selection only establishes the POWER UP STATE of the tilt sense function. If ENABLED the unit
will power up with the tilt indicator functioning. Regardless of this menu selection, the tilt function can be
enabled or disabled via an acoustic command (if selected), see section 7.1.

Enter Tilt Power Up State, (E)nabled or (D)isabled: D

8.0

MAINTENANCE

8.1

Step-by-Step Turnaround Procedure for the 865-A

One big advantage of the Benthos 865-A Acoustic Release is its simple, low maintenance design which
allows for very quick shipboard turnarounds. The following turnaround procedure and checklist are
provided for ease of maintenance at sea.

Tools Needed

Parts Needed

Bristle brush

Battery Pack: 865-SB-13

Screwdriver

3/8" ignition wrench or small
adjustable wrench

Voltmeter, ohmmeter

Anode Kit: 865-SA-K

3/4" open end wrench

Silicone grease

3/4" socket wrench

Benthos Deck Unit: DS-7000

Scotch brite or wire brush

Benthos Expendable Link: 865-SL

STEP 1: RECOVERY

Promptly scrub the unit down with fresh water and bristle brushes. Clean all scum off of the transducer.
Remove and discard all old anodes, but save the mounting hardware.

STEP 2: REPLACE BATTERY PACK.

a.

Move unit to a clean, dry workbench. Turn the release off by turning switch to HOLD-EXTEND.
Open housing and slowly slide chassis assembly out, being careful not to scratch the O-ring
surfaces. Unplug the battery pack connector. Remove the battery/electronics package by
removing two nuts on opposite side of release mechanism mounting plate and pulling straight out
(see Figure 8-1).

«
...
33
34
35
36
37
...
»

Содержание 865-A





































































Отзывы:

Нет отзывов

Похожие инструкции для 865-A

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: HoMedics Страницы: 10

Madingley Hall CB23-DAB-WHT/BLK

Бренд: MAJORITY Страницы: 20

Бренд: JRC Страницы: 332

Бренд: Garmin Страницы: 59

Бренд: JVC Страницы: 32

Бренд: Teledyne Страницы: 48

Бренд: Seiwa Страницы: 8

Бренд: Telefunken Страницы: 14

Бренд: trig Страницы: 16

Marr (South) SRM9030plus

Бренд: Scot-tel Gould Страницы: 2

Бренд: Sytech Страницы: 7

Бренд: Cobra Страницы: 20

Бренд: Cobra Страницы: 11

Бренд: Cobra Страницы: 22

Бренд: Cobra Страницы: 21

Бренд: Cobra Страницы: 21

MR HH 500 FLT BT EU

Бренд: Cobra Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды