n
Arm — B Mode
This operation will Arm and Disarm the Partitions in ac-
cordance with the
B Mode
Arming configuration (pro-
grammed by the Installer).
1.
Hold the Key near the sensitive field of the Reader:
the light indicators will light in turn (at 2 second in-
tervals), as shown in Figure 5.
2.
Remove the Key when the
Red
and
Green
light in-
dicators are ON (Figure 5d): at this point the system
will Arm in
B Mode
.
+
When the Reader’s
EN50131
option is DISABLED,
the
Green
light indicator turns OFF when you re-
move the Key, if the Key’s Partitions does not
match the Reader’s Partitions.
For example:
if a Key is assigned to the
Partition n. 1
and a Reader is assigned to the
Partitions n. 1 and 2
,
the
Green
light indicator turns ON when you hold the
Key near the Reader; when you remove the Key from
the Reader,
only the Partition n. 1
arms in
B Mode
and the
Green
light indicator
turns OFF
.
n
Disarm Patrol
Keys with the
Patrol
option can Disarm the system for
the programmed Patrol Time.
n
False Key
When an unrolled (false) Key is present at the Reader,
ALL the Reader’s light indicators fast blinking.
+
A Reader tamper will be generated if you present
10 time a false Key at the Reader.
The Wireless Key
If your system is equipped with a Wireless Receiver, it
will be possible to control all the main functions from re-
mote locations by means of Wireless Keys (see Fig-
ure 6). This paragraph describes the functions that can
be controlled by Wireless Keys.
+
The operations performed by Wireless Keys will
not be confirmed by any type of feed back signal
(audible or visual), unless done in the vicinity of a
Reader or a Keypad, or a device that has been es-
pecially set up to provide feed back signals.
n
Away Arming (
<
)
Press the button until the LED turns ON (see Fig. 6), to
Arm all the Partitions
of the Wireless Key in use.
n
Stay Arming (
=
)
Press the button until the LED turns ON (see Fig. 6), to
Arm the system in
A
Mode.
n
Disarming (
>
)
Press the button until the LED turns ON (see Fig. 6), to
Disarm all the Partitions
of the Wireless Key in use.
n
Other functions (
!
)
Press the button until the LED turns ON (see Fig. 6), to
activate the special functions programmed for the Wire-
less Key in use (example: B Mode
arming, Superkey or
both).
n
Low Battery
If any of the Wireless Key batteries starts to run low, the
G
LED on the Keypads will Turn ON.
+
All the system Trouble conditions are signalled by
the
G
LED. Therefore, if this LED turns ON, you
must access the
View Trouble
Mode for details.
The Low Wireless Battery condition will be signalled in
View Trouble
Mode by the [
Bat.low WLS
] message
(refer to “View Trouble Mode” in the “OPERATING
YOUR SYSTEM FROM A KEYPAD” section).
The Event Logger will provide the details of the Wire-
less key that has triggered the Low battery condition.
A
In accordance with the EN50131-1 standard, the
system does not arm if there is a low battery condi-
tion, when you perform an arming request: the ex-
ternal siren will emit a double squawk. You can
verify the cause that inhibits the arming (low bat-
tery), through an LCD keypad, and force the arm-
ing: the external siren will emit a squawk to signal
the arming.
Call your installer and have the battery replaced.
54
Expandable Hybrid Control Panel
ABSOLUTA
LED
+
Panasonic
CR2025
3V
Figure 6
Wireless key.
Содержание ABSOLUTA ABS104M50
Страница 67: ......
