background image

                                                                                   

2013/7/25

                                                                   

19

 

Chapter 6 Certification

Chapter 6 Certification

Chapter 6 Certification

Chapter 6 Certificationssss    

6.1 IEC Certification 

 

The  PV  modules  provided  by  BenQ  Solar  all  pass  the  design  qualification  and  type 

approval standard IEC 61215 edition 2. 

 

The PV modules provided by BenQ Solar all pass the safety qualification standard IEC 

61730 certified for application class A. 

 

Modules  qualified  for  safety  through  EN  IEC61730.1  and  EN  IEC61730.2  within  this 

application class are considered to meet the requirements for Safety Class II. 

 

6.2 ETL Certification 

 

This product meets or exceeds the requirements set forth by UL1703 for PV Modules.   

 

This UL1703 Standard covers flat-plate PV modules intended for installation on buildings 

and those intended to be freestanding.   

 

To  satisfy  the  listing  for  this  product  the  modules  must  be  mounted  with  a  rack  or 

standoff structure.   

 

It does not include integration into a building surface because additional requirements 

may apply.   

 

This product is not intended for use where artificially concentrated sunlight is applied to 

the module. 

 

 

 

 

 

 

 

 

 

 

 

 

BenQ Solar is a division of AU Optronics 

© Copyright AUO Optronics Corp.    All rights reserved.    AUO reserves the right to update, delete or modify 

the information at any time without prior notification.    All modifications and amendments shall be effective 

immediately. 

Содержание PM096B00





















Отзывы: