Benefon SERAPH NT Скачать руководство пользователя страница 31

Страница: 31 / 56

USER INTERFACE 31

PART C: OPERATING THE SERAPH

PART C: OPERATING THE

SERAPH

USER INTERFACE

Turning the device on

1. To power on the device, press the upmost side key

and

hold it down for a few seconds.

2. The logo will be shown.

3. An automatic PIN code entry will take place. If the PIN

code is requested, the PIN code must be programmed in
the device in advance. For more information, see

AUTO-

MATIC PIN ENTRY ON PAGE 30

4. The device will remove all short messages found on SIM

card and go to stand-by mode. The device may also no-
tify the service center of the power on. For more infor-
mation, see

SETTINGS FOR MANUAL POWER ON AND OFF ON

PAGE 27

There are two other ways to power on the device:

•By pressing the BeneGuard button

and holding it

down for a few seconds. NOTE: This action will start the
emergency cycle (unless cancelled in time).

•By connecting the device to a charger.

IDE

KEYS

•Upmost:

Power on/off

•Middle: For

increasing volume

•Lowmost: For

decreasing
volume and silen-
cing ringing tone

ISPLAY

•GSM status

•GPS status

•Battery status

ENEGUARD

BUTTON

For making emergency
calls/sending emergen-
cy messages

ATTERY

Battery release
catch

YSTEM

CONNECTOR

For connecting
charger or data
cable to the
device.

ICROPHONE

Plug for external
GPS antenna

GPS

ANTENNA

END

KEY

•For making

information call/
sending position

•For answering calls

OUDSPEAKER

KEY

•For rejecting/

ending calls

•For cancelling

some operations

NOTE: If the PIN code is incorrect or the SIM card is
not inserted at all, the normal network connection is
unavailable and the device can only be used for ma-
king network emergency calls (e.g. 911, 112).

Содержание SERAPH NT
























































Результаты поиска

Содержание SERAPH NT

Отзывы:

Бренды по названию

Популярные бренды

Benefon SERAPH NT, Руководство по эксплуатации

Результаты поиска

Содержание SERAPH NT

Отзывы:

Бренды по названию

Популярные бренды