BendPak HD-9 Скачать руководство пользователя страница 46

Страница: 46 / 92

HD-9 Series Four-Post Lifts

P/N 5900123 — Rev. M — February 2020

Installing the Power Unit

This section describes how to

install

, but not make the connections to, the Power Unit for your Lift.

An Electrician is

not

needed to install the Power Unit; one is required to connect the Power Unit to its

power source.
The Power Unit

must

be installed on the Power Post; attach it to one of the two Mounting Brackets,

whichever is more convenient for the installation.

Important

Many people install the Flex Tube Bracket Plate and/or the Zero Angle Bracket at the
same time as they install the Power Unit. Read

Installing the Flex Tube

and

Installing the Pushbutton Air Valve

for more information to see if this makes

sense for your installation.

⚠

DANGER

Risk of explosion: The Power Unit has internal arcing or parts that may spark and
should not be exposed to flammable vapors. Never expose the Power Unit motor
to rain or other damp environments. Damage to the motor caused by water is

not

covered by the warranty.

Tip

The Power Unit is heavy. We recommend you have one person hold the Power Unit while
another person bolts it in place.

The following drawing shows how to attach the Power Unit to the Power Post.

Side view of Power Post. Not drawn to scale. Not all components are shown.

Содержание HD-9




























































































Результаты поиска

Содержание HD-9

Отзывы:

Похожие инструкции для HD-9

Бренды по названию

Популярные бренды

BendPak HD-9, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-9

Отзывы:

Похожие инструкции для HD-9

Бренды по названию

Популярные бренды