BendPak HD-7ZM Скачать руководство пользователя страница 27

Страница: 27 / 56

STEP 12

( Power Unit Hook Up )

1. Have a certified electrician run the power supply to

motor. Refer to the data plate found on the motor for

proper power supply and wire size.

RISK OF EXPLOSION

This equipment has internal arcing or parts that may

spark and should not be exposed to flammable vapors.

Motor should not be located in a recessed area or below

floor level. NEVER expose motor to rain or other damp

environments. DAMAGE TO MOTOR CAUSED BY

WATER IS NOT COVERED UNDER WARRANTY.

STEP 13

( Inspecting The Slack Safety Springs )

The following steps involve the SLACK CABLE SAFETY

DEVICE and MAIN SAFETY. Failure to follow these

steps could result in serious injury or death in the event

of cable failure.

1. Inspect the ends of the ALL SAFETY LOCK

SPRINGS as shown. Make sure the spring ends are

secure at both ends.

DO NOT ATTEMPT TO RAISE

THE LIFT UNTIL THE SLACK SAFETY SPRINGS ARE

ATTACHED AND THE ROLLERS ARE PULLED

CLEAR FROM THE LADDER.

(See Fig. 13.1)

2. Repeat this step for each corner of the lift.

STEP 14

( Lift Start Up / Final Adjustments )

1. Make sure the Power Unit reservoir is full with 12

quarts of 10-WT hydraulic oil or Dexron-III automatic

transmission fluid.

2. Spray the inside of the Columns where the Slide

Blocks glide with a light lubricant or WD-40.

3. Test the Power Unit by pressing the push-button

switch. If the motor sounds like it is operating properly,

raise the lift and check all Hose connections for leaks. If

the motor gets hot or sounds peculiar, stop and check all

electrical connections.

4. Before proceeding, double-check to make sure all

cables are properly positioned within the grooves of ALL

Sheaves. Make sure all Cable Sheave retaining Pins

and/or Clips are secure.

IMPORTANT NOTE:

CAUTION Never operate the motor on line voltage

less than 208V. Motor damage may occur which is not

covered under warranty. Have a certified electrician run

appropriate power supply to motor. Size wire for 25amp

circuit. See Motor Operating Data Table.

IMPORTANT: Use separate circuit for each power unit.

Protect each circuit with time delay fuse or circuit break-

er. For single phase 208-230V, use 25 amp fuse.

Three phase 208-230V, use 20 amp fuse. For three

phase 400V and above, use 15 amp fuse. All wiring

must comply with NEC and all local electrical codes.

Fig. 12.1

Fig 13.1

Make sure the ends

of all three (3) springs

are securely attached

to the Safety Locks

and Cross Cube

anchor points.

Содержание HD-7ZM

























































Результаты поиска

Содержание HD-7ZM

Отзывы:

Похожие инструкции для HD-7ZM

Бренды по названию

Популярные бренды

BendPak HD-7ZM, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-7ZM

Отзывы:

Похожие инструкции для HD-7ZM

Бренды по названию

Популярные бренды