background image

21

A-3

Compressor with up to 25% duty cycle

Footnotes:

  

1. With increased air demand the air dryer cartridge needs to be 

replaced more often.

2.  Use the drain valves to slowly drain all reservoirs to zero psi.

3. Allow the oil/water mixture to fully settle before measuring oil 

quantity.

4.  To counter above normal temperatures at the air dryer inlet, (and 

resultant oil-vapor passing upstream in the air system) replace the 

discharge line with one of a larger diameter and/or longer length.  

This helps reduce the air's temperature.  If sufficient cooling occurs, 

the oil-vapor condenses and can be removed by the air dryer.  

Discharge line upgrades are not covered under warranty.  Note: 

To help prevent discharge line freeze-ups, shorter discharge line 

lengths or insulation may be required in cold climates.  

(See Bendix 

 

 

 

 

 

Recom-  Recom- Acceptable

 

 

  Typical  Discharge 

mended  mended Reservoir

 

 

 

Compressors 

Line 

Air Dryer 

Reservoir 

Oil Contents

3

 

 

No.  of 

Spec'd 

        

Cartridge 

Drain 

at Regular 

 

 

Axles 

 

       

Replacement

1

 Schedule

2

 

Drain Interval

High Air Use 

Low Air Use

 

e.g.  Double/triple trailer, open 

highway coach/RV, (most) 

pick-up & delivery, yard or 

terminal jockey, off-highway, 

construction, loggers, concrete 

mixer, dump truck, fire truck.

e.g.  Line haul single trailer 

w/o air suspension, air over 

hydraulic brakes.

e.g.  Line haul single trailer 

with air suspension, 

school bus.

5

or

less

5

or

less

8

or

less

12

or

less

Table A:  Maintenance Schedule and Usage Guidelines

Recom-

mended

Every

Month - 

Max of  

every 90 

days

Every

Month

Every 3

Years

Every 2

Years

Every

Year

I.D.

Vehicle Used for:

Column 1

Column 2

Column 3

Column 4

Column 5

Regularly scheduled maintenance

 

is the single most important factor in maintaining the air brake charging 

system.

Length        

6 ft.

1/2 in.

9 ft.

1/2 in.

12 ft.

1/2 in.

3/4 in.

12 ft.

BASIC test

acceptable 

range:

5 oil units

per month.

See 

Appendix

A.

For oil carry-over 

control

suggested 

upgrades:

5/8 in.      15 ft.

For oil carry-over 

control

suggested 

upgrades:

5/8 in.      9 ft.

For oil carry-over 

control

suggested 

upgrades:

5/8 in.      12 ft.

Compressor with less than 15% duty 

cycle

Compressor with up to 25% duty cycle

Compressor with up to 25% duty cycle

Bendix

®

 BA-921

®

 or SNA-01

 air compressor 

Bendix

®

 T

u-

Flo

®

 550 air compressor 

Bendix

®

 T

u-

Flo

®

 750 air compressor 

Bendix

®

 BA-922

®

or DuraFlo 596

™ 

air compressor

Bendix

®

  

BASIC

 test

acceptable 

range:

3 oil units

per month.

See 

Appendix

A.

For the

BASIC 

Test Kit:

Order

Bendix

P/N

 

5013711

e.g.  City transit bus, refuse, 

bulk unloaders, low boys, 

urban region coach, central 

tire inflation.

(See footnote 7)

Bulletins TCH-008-021 and TCH-008-022, included in Appendix B, 

for more information.)

5.  For certain vehicles/applications, where turbo-charged inlet air is 

used, a smaller size compressor may be permissible.

6.  Note: Compressor and/or air dryer upgrades are recommended 

in cases where duty cycle is greater than the normal range (for 

the examples above).   

7.  For correct compressor upgrades consult Bendix - Please note 

that because a compressor is listed in the same area of the chart 

it does not necessarily mean that it would be a suitable candidate 

for upgrade purposes.  

 

For Bendix

®

 Tu-Flo

®

 550 and 750 compressors, unloader service is 

recommended every 250,000 miles.

Содержание SNA-01










































Отзывы: