manualshive.com logo in svg

Bender ISOMETER iso1685FR, Руководство пользователя

Поделиться
Скачать
Bender ISOMETER iso1685FR Скачать руководство пользователя страница 46

Technical data

46

iso1685FR(M)_D00002_02_M_XXEN/06.2017

Serial interfaces

Interface/protocol iso1685FR.......................................................................................................................................................................................RS-485 / BMS (slave)
Interface/protocol iso1685FRM ......................................................................................................................................RS-485 / BMS (Slave), Modbus RTU (switchable)
Connection........................................................................................................................................................................................................................ bus: Terminals A/B
.............................................................................................................................................................................................................................................Shield: Terminal S
Cable length .................................................................................................................................................................................................................................  ≤  1200 m
Shielded cable (shield to PE on one side)......................................................................................................................................2-core, Ø 0.6 mm

2

, e.g. J-Y(St)Y 2 x 0.6

Terminating resistor, switchable (switch RS-485 Term.) ...................................................................................................................................................... 120 Ω (0.5 W)
Device address, BMS bus, adjustable (DIP switch) iso1685FR .................................................................................................................................................  2…33 (2)*
Device address, BMS bus, adjustable (DIP switch) iso1685FRM .............................................................................................................................................  2…17 (2)*

Switching elements

Switching elements............................................................................... 3 changeover contacts: K1 (insulation fault), K2 (insulation fault redundant), K3 (device error)
Operating principle K1, K2 ........................................................................................................................................................................... N/C operation, not changeable 
Operating principle K3 ........................................................................................................................................................................... N/C operation, cannot be changed 
Contact data acc. to IEC 60947-5-1:
Utilisation category .................................................................................................................................................................................  AC 13 AC 14 DC-12 DC-12 DC-12
Rated operational voltage  ..............................................................................................................................................................................  230 V 230 V24 V110 V220 V
Rated operational current.........................................................................................................................................................................................   5 A 3 A 1 A 0.2 A 0.1 A
Minimum contact rating  .......................................................................................................................................................................................... 1 mA at AC/DC ≥ 10 V

Connection via terminals (except system coupling)

Connection type...........................................................................................................................................................................................  pluggable push-wire terminals
Connection, rigid/flexible..........................................................................................................................................................................  0.2…2.5 mm

2

/0.2…2.5 mm

2

Connection flexible with connector sleeve, without/with plastic sleeve .......................................................................................................................... 0.25…2.5 mm

2

Conductor sizes (AWG) ..................................................................................................................................................................................................................... 24…12

Connection of the system coupling

Connection type...........................................................................................................................................................................................  pluggable push-wire terminals
Connection, rigid/flexible............................................................................................................................................................................. 0.2…10 mm

2

 / 0.2…6 mm

2

Connection, flexible with ferrules, without/with plastic sleeve  ...............................................................................................................  0.25…6 mm

2

/0.25…4 mm

2

Connection AWG/kcmil...................................................................................................................................................................................................................... min. 24
Conductor cross section AWG/kcmil ................................................................................................................................................................................................... max. 8

Environmental conditions

EMC EN 61326-2-4
EMC except, IEC 61000-4-3 (Radiated immunity 80MHz - 1GHz): .....................................................................................................................................................8V/m
Ambient temperatures:
Operating temperature........................................................................................................................................................................................................... -25…+ 70 °C
Transport................................................................................................................................................................................................................................. -25…+ 80 °C
Long-term storage ................................................................................................................................................................................................................. -25…+ 80 °C
Classification of climatic conditions acc. to IEC 60721:
Stationary use (IEC 60721-3-3) ........................................................................................................................................ 3K5 (except condensation and formation of ice)
Transport (IEC 60721-3-2) ......................................................................................................................................................................................................................  2K3
Long-time storage (IEC 60721-3-1)........................................................................................................................................................................................................  1K4
Classification of mechanical conditions acc. to IEC 60721:
Stationary use (IEC 60721-3-3) ...............................................................................................................................................................................................................3M4
Transport (IEC 60721-3-2).......................................................................................................................................................................................................................2M2
Long-term storage (IEC 60721-3-1) ..................................................................................................................................................................................................... 1M3

Содержание ISOMETER iso1685FR





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды