Bell VSD 42/12, Руководство по эксплуатации и техническому обслуживанию

Страница: 25 / 64

25
D22002000 - ver.2 - UPD 291209
ENGLISH
3.1.B - For machines with connection to the hydraulic system of the tractor (VSD IT)
•
Never connect the log splitter with the tractor moving.
•
Use only fast-disconnect hydraulic fittings, of the correct size and always check that they are correctly fastened and tight.
3.1.C - For machines driven by cardan shaft (VSD Comby - VSD GC)
WARNING
Use CE-marked cardan shaft only. Carefully follow the manufacturer operating instructions
•
Never connect the log splitter with the tractor moving.
•
Make sure that the machine is properly fixed to the 3 points of the tractor.
•
Make sure that the cardan shaft is fully inserted in the power take-off and has clicked in place.
•
Never touch the cardan shaft with the engine running.
4 - OPERATING THE MACHINE
Before transporting the log splitter it is necessary to assemble the low supports of the 3-points attachment to the
tractor
•
Unscrew the nut and remove the screw (C in fig.4, page 2)
•
Insert the support (D in fig.4) and fix it with the appropriate screw by locking the nut
•
The log splitter, in compliance with standard EN 609-1, is activated with a two hand control: the machine will function only when both the
levers are activated together (1 and 2 in fig.12, page 4).
•
Never use the log splitter if it is not in perfect order or if it needs servicing. Before starting work, check correct functioning of all the safety devices
(two hands control and switch-off button).
•
Lower the two log support arms as shown in figure 5, page 3
•
Before starting work, check the integrity of the flexible pipes and the lack of leaks in the connections, check the level of the hydraulic oil in the tank
and top up if necessary with one of the oils indicated on page 23.
The level of the oil must be between the two notches on the rod of the oil plug (14 in fig.1, page 2).
•
Before starting work, switch on the log splitter and let the oil warm up for a few minutes.
4.1.A - For machines with electric motor (VSD Comby - VSD T)
If the motor does not run in the correct direction, invert two of the phases in the socket. Remove the plug from the log splitter. Insert a suitably sized
slot head screwdriver in the slot located inside the plug of the switch as shown in figure 3, page 2. Exert slight pressure, turn the white disc by
180°. This operation physically inverts two poles on the three-phase motor.
Check that the motor runs in the correct direction as indicated by the arrow.
Never open the box containing the switch, or open the terminal block on the motor. If it is necessary to do
so, have these operations carried out by your electrician.
If the fuses blow or the protection valve trips, this means that you are overloading the motor or the electrical installation is not correctly rated. Consult
your electrician.
4.1.B - For machines with connection to the hydraulic system of the tractor (VSD IT)
•
Make sure the tractor is off, that the parking brake is on and if necessary that the wheels are chocked.
•
Before starting work, always check that none of the hydraulic tubes is damaged.
•
Connect the oil delivery tube (marked with a special flat white clip) of the log splitter and the discharge tube (no marking) to the hydraulic system
of the tractor.
•
Make certain that all unions are tight and that there is no leakage of oil.
•
Apply a pressure not exceeding 220 bar to the hydraulic circuit of the log splitter.
•
Perform a few cycles without wood before starting work so as to vent any air present in the hydraulic circuit.
•
When disconnecting the machine from the hydraulic system of the tractor, take care not to spill any oil, and remember to replace the plugs on the
two tube unions.