manualshive.com logo in svg

Bell System bellswipe, Руководство пользователя, Страница: 3 / 21

Поделиться
Скачать
Bell System bellswipe Скачать руководство пользователя страница 3

bell

swipe

 Card Access System

System/Card  Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Summary of function cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Programming the Lock Release time . . . . . . . . . . . . . . . . . . . . . . . . 20

Enabling or Changing a group of cards . . . . . . . . . . . . . . . . . . . . . . 21

Adding or Changing a card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Disabling a User Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Deleting all user cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

The TEST LOCK card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Engineering Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Restoring Factory Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Enabling the starter Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Replacing the function cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Summary of LED operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Fault Finding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

bell

swipe

 Card Access System

1

General Description

The 

bell

swipe

 Card Access System is a high quality security product for

controlling access to offices and apartments using proven Magstripe technology.

 A Bellswipe reader should be installed adjacent to the building entrance, and the

door  fitted with an electric lock release or magnetic lock. Authorised personnel

are each issued with an individual BellSwipe card. Swiping a valid card through

the reader will result in the door being released for a few seconds. A Time-clock

may be used to restrict access to certain card holders to specific times of the day

or week.

Basic Operation

When a valid user card is swiped through the reader the green LED illuminates

and the electric lock release operates for a predetermined time (1-250 seconds).

If an invalid card is swiped the red LED illuminates for 1 second and the lock

release does not operate. A card may be invalid either because it has not been

enabled on the system or its use has been restricted to another  time period. 

Swiping a Card

Swipe in the direction indicated by the arrows on

the reader and on the card, ensuring the black

Magnetic stripe passes through the reader .

Содержание bellswipe






















Отзывы:

Нет отзывов