Bell System bellswipe Скачать руководство пользователя страница 2

Страница: 2 / 21

bell

swipe

Card Access System

System features

Up to 500 User cards.

Two Time Zones for Staff / Executive operation.

Outputs for Fail-safe and Fail-secure locks plus one isolated contact

Shadow cards for easy deletion of User cards

Eight function cards for easy system programming.

Hi-Co Cards for a long durable life: Secure encrypted card data.

Separate Control unit for maximum security.

Combined Power Supply and Control Unit for simplified installation.

Card data is retained after power failure using EEPROM.

Optional battery backup for operation during mains power failure.

BS500 Kit Components

CR500 Control Unit with integral Power Supply

RH10 Card Reader

203 Lock Release (fail-secure)

BSF Starter Pack of cards ( 8 Function cards + 16 user cards & shadow cards)

Optional Components

Part No.

Description

BS20C

Additional pack of cards for 20 users (includes shadow cards)

TS2000

Time Clock, 7 day, quartz reserve, 12V operated

BAT02

12V 2AH Battery for CR500

bell

swipe

Card Access System

Contents

General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Time-restricted access (Staff / Executive operation) . . . . . . . . . . . . . . 2

Exit Facility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Integrated Power Supply with optional battery backup . . . . . . . . . . . . 2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

CR500 Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

RH10 Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Electric Lock Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Isolated Lock Relay Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

High Current Lock Releases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Time Restricted Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Exit Facility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

BS500 Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adding further User cards . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Содержание bellswipe






















Результаты поиска

Содержание bellswipe

Отзывы:

Похожие инструкции для bellswipe

Бренды по названию

Популярные бренды

Bell System bellswipe, Руководство пользователя

Результаты поиска

Содержание bellswipe

Отзывы:

Похожие инструкции для bellswipe

Бренды по названию

Популярные бренды