Belkin F5D7230-4 Скачать руководство пользователя страница 13

Страница: 13 / 59

Hardware Description &
Installation

2.1 Physical Outlook

Front Panel

The following illustration shows the front panel of the Wireless
Broadband Router :

LED Indicators

The Wireless Broadband Router is equipped with eight LEDs on
the front panel as described in the table below (from left to right) :

LEDs

Function Color

Status

Description

Off

No power is supplied to the unit.

Power Green

Solid

Power is connected to the unit.

Off

WLAN interface is not initialized

properly.

WLAN interface is initialized properly

and ready.

WLAN Wireless

Ready/

Activity

Green

Blinking

Transmitting/receiving packets to/from

WLAN interface.

LAN 1-4

LAN port

Status

Green

(100 Mbps)

Off

Power is off or no Ethernet device is

connected.

Содержание F5D7230-4




























































Результаты поиска

Содержание F5D7230-4

Отзывы:

Похожие инструкции для F5D7230-4

Бренды по названию

Популярные бренды

Belkin F5D7230-4, Руководство пользователя

Результаты поиска

Содержание F5D7230-4

Отзывы:

Похожие инструкции для F5D7230-4

Бренды по названию

Популярные бренды