Belanger H2AIR ARCH Скачать руководство пользователя страница 42

Страница: 42 / 72

H2AIR

ARCH

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL958

Maintenance

Routine Procedures

H2AIR® Arch (Daily)



Clean and inspect the wash tunnel for debris.



Inspect all LED lights. Clean or replace as necessary.



Visually check the spray of each of the nozzles. Clean or replace as necessary.



Visually inspect all hoses and airlines for damage or wear. Replace as necessary.



Inspect the arch for clogged nozzles. This can best be done while running a test vehicle at the
start of the business day. Insert a thin wire into the nozzle opening to clear any obstructions.
Sometimes simply tapping on the nozzle can clear it.



Run a test wash

H2AIR® Arch (Monthly)



Inspect all fasteners and anchors on the frame and any additional components.



Inspect the air pressure on the air panel regulators. Adjust as necessary.



Wash component down with a good degrimer such as Tide laundry detergent and hot water.

Содержание H2AIR ARCH









































































Результаты поиска

Содержание H2AIR ARCH

Отзывы:

Похожие инструкции для H2AIR ARCH

Бренды по названию

Популярные бренды

Belanger H2AIR ARCH, Руководство пользователя

Результаты поиска

Содержание H2AIR ARCH

Отзывы:

Похожие инструкции для H2AIR ARCH

Бренды по названию

Популярные бренды